HP Officejet 5610 All-in-One Printer support
Print Cartridge Errors
HP Officejet 5600 series - Print Cartridge Errors
After you install a print cartridge, the attention light begins to flash red. The printer will not print. One of the following messages may appear on the control panel:
- Color or Right Print Cartridge is not compatible
- Incorrect Print Cartridge(s)
- Print Cartridge Problem
- Incorrectly Installed Cartridge(s)
- Black or Color Cartridge(s) Failed
Work through the sections below in order. When the attention light stops blinking, you have solved the problem.
NOTE:In the procedures below, the "problem" cartridge is identified by the blinking attention light. Either one or both of the cartridges could be causing the problem.
Step 1: Remove, inspect, and reseat the problem cartridge
The print cartridge may not have full electrical contact with the product. Removing and reinstalling the cartridge might help.
NOTE:HP cannot guarantee the quality of remanufactured or refilled cartridges. Use genuine HP print cartridges to ensure good quality.
- Make sure the product is on. Press the Power button if it is not lit.
- Open the product cover, then wait until the print carriage is idle and silent.
- Press down lightly on the end of the problem cartridge to release it.
- Slide the cartridge out, and inspect it.CAUTION:Do not touch the copper electrical contacts or the ink nozzles.Check the electrical contacts for debris. If any debris is evident, proceed to step two.Make sure all the clear nozzle protective tape has been removed.CAUTION:Do not attempt to remove the copper electrical strip.Look at the number on the print cartridge label, and make sure it is compatible with the product. Compatible print cartridges are listed in the Printer Reference Guide supplied with the product.
- If the cartridge is compatible, reinstall it.
- Cartridges marked with a triangle, go into the left carriage slot.
- Cartridges marked with a square or pentagon, go into the right carriage slot.
- Close the product cover.
- Try to print again. If the issue persists, continue to the next step.
To view a demonstration of how to remove and replace print cartridges, follow these steps:
- Click the Start button and click the HP Solution Center icon to open the toolbox.
- Under Device Support, click the How do I button to display a list of topics.
- Select Replace print or ink cartridges , drag your cursor right, and click the printer's name. The video will start.
Step 2: Clean the problem cartridge contacts
- Gather the following items to clean the cartridge and carriage:
- Clean distilled water. Use bottled or filtered water if distilled water is not available. Tap water can contain contaminants that damage the cartridge.
- Clean cotton swabs or any soft, lint-free material that will not stick to the cartridges (coffee filters work well).
- Sheets of paper or a paper towel to rest the cartridge on during cleaning.
- Open the product cover and wait until the carriage is idle and silent.
- Remove the cartridge and place it on a piece of paper with the nozzle plate facing up.NOTE:Clean the contacts quickly so that the cartridge is not outside of the product for more than 30 minutes. If the cartridge is outside of the product for too long, the ink can dry and clog the nozzles.
- Unplug the product from the electrical outlet.
- Dip the swab or other cleaning material in the water and squeeze it to remove most of the moisture. The swab should be only slightly damp.
- Clean the cartridge contacts.CAUTION:Do not touch the ink nozzles.
- Clean the contacts in the carriage.
- Either let the cartridge sit for 10 minutes to allow the cleaned area to dry, or use a new swab to dry it.
- Reinstall the cartridge.
- Reconnect the product to the electrical outlet.
- Close the product cover.
Step 3: Repeat reseating and cleaning steps
If the problem is not solved, repeat the reseating and cleaning procedures above.
Step 4: Contact HP
If a cartridge replacement was not tried previously to solve this problem, replace the problem cartridge now. Click here (c00206040) (in English) to see if the cartridge is covered under warranty.
Which cartridges you use depends on your country or region. Follow these steps to purchase cartridges or check cartridge compatibility for your printer using HP SureSupply.
- Click this link, HP SureSupply .
- Scroll to the bottom of the page and make sure that the country or region location is correct.
Step 5: Print in backup mode
If you do not have a replacement cartridge, you can still print in ink backup mode. Simply remove the problem cartridge, and print with the remaining cartridge.
- If you remove the tri-color cartridge, printouts will be in grayscale.
- If you remove the black or photo cartridge, the product prints slowly and the colors in the printouts might differ.