Jump to content

Motherboard Specifications, P4SD-LA (Stingray)

  • PrintPrint

Motherboard specifications table

Feature/SpecificationDescription
Motherboard Description
  • Manufacturer's name - ASUS P4SD-LA
  • HP/Compaq name - Stingray
Motherboard SupplierASUS
System BIOS SupplierASUS/Award
Board Form FactoruATX
Processor BrandIntel
Processor Socket TypemPGA478
Processor FamilyPentium 4HT
Maximum Processor Core FrequencyUp to 3.2 GHz P4 Northwood
Processor Front Side Bus800/533/400 MHz
Hyper Threading SupportYes
Processor VRM SpecificationNorthwood FMB2
Chipset 'North Bridge'865G
Chipset 'South Bridge'ICH5
Super I/O SMsC LPC47M192-NC
Flash BIOS Device Type and DensityFWH 4 Mbit
Memory TypeDDR SDRAM (Supports duel channel)
Memory SpeedPC3200 (400 MHz),

PC2700 (333 MHz),

PC2100 (266 MHz)
Memory SocketsFour DDR DIMM (184-pin)
Single or Dual Channel Dual System Memory
Maximum Memory Supported4GB (4 x 512MB) unbuffered (HP and Compaq recommend 2GB)
AGP Graphics SupportYes
AGP Graphics Maximum ModeAGP 8x
Integrated Graphics SupplierIntel
Integrated Graphics Shared (UMA) MemoryUp to 64 MB Intel DVMT- dynamic (32 MB if less than 256 MB system memory)
Graphics ConfigurationIntegrated on motherboard
Graphics ConnectorAGP 8x (available)
TV-out Device or ConfigurationNo
Integrated Audio TypeAC'97
AC'97 Codec DeviceRealtek ALC650
5.1 (Dolby) Channel Audio SupportYes, Six speaker mode (requires audio driver and software setting changes)
Passive Speaker Output (amplifed)Speaker-out header
Rear Audio JacksMicrophone,

Line-in,

Line-out,
Front Audio ConnectorsHeadphones,

Microphone,

Line-in
Ethernet 10/100 LAN SupplierPCI Realtek RT8101L
Ethernet ConfigurationIntegrated, Down
IEEE 1394 SupportConfiguration: Integrated on motherboard

MAC/PHY Device: TI TSB43AB22

Maximum transfer rate: 400MBps

Ports: Two total (1 front, 1 back)
IDE/ATAPI UDMA Modes2 IDE connectors Supports. 2 IDE devices on each connector. Supports UDMA 100/66/33 - requires an 40 pin/80 conductor cable for UDMA 66 and 100 disk drives

2 SATA connectors Supports. 1 Serial ATA-150 disk drive on each connector
Expansion SlotsOne AGP,

Three PCI,

One Ultra ATA
USB Ports Supports up to 8 USB v2.0
USB Front/Rear OptionsUp to four front, four rear
Rear External PortsOne serial,

One parallel,

One floppy,

Two PS/2 (keyboard and mouse),

One IEEE 1394,

Four USB,

One VGA Monitor
Front External PortsTwo USB, One IEEE 1394
Fan supportHeaders for CPU and System

CPU Fan Speed Control for active fansink

System Fan Speed Control
Available Manufacturer OptionsIntegrated graphics (G),

Integrated LAN (L),

Six speaker mode, Dolby 5.1 (6)

Integrated 1394 (E)

Motherboard layout and photos

Figure 1: Photo
Figure 2: Layout of the P4SD-LA GL6E motherboard
Figure 3: Backplate
1 - Mouse
2 - Parallel
3 - IEEE 1394 FireWire
4 - LAN
5 - Line-In
6 - Line-Out
7 - Microphone
8 - USB
9 - VGA
10 - Serial
11 - Keyboard

Clearing the CMOS settings

The 3-pin J19 jumper allows you to clear date, time, and system setup parameter memories in CMOS. The onboard button cell battery powers the RAM data in CMOS, including system setup information.
CAUTION: Do not change any jumper setting while the computer is on. Damage to the motherboard can result.
  1. Turn off the PC and unplug the power cord.
  2. Move the J19 jumper cap from pins 1-2 (normal) to pins 2-3 (clear CMOS).
  3. Keep the J19 jumper cap on pins 2-3 for 5 to 10 seconds, then move it back to pins 1-2.
  4. Plug in the power cord and turn on the PC.
  5. Enter the BIOS setup to change the BIOS settings.

HP Support forums

Find solutions and collaborate with others on the HP Support Forum
HP.comHP on FacebookHP on TwitterHP on YouTubeHP on Linked InHP on FlickrHP on Google+