Jump to content

Motherboard Specifications, IPILP-LC (Lancaster8)

  • PrintPrint
Figure 1: The IPILP-LC (Lancaster8) motherboard
  • Manufacturer's motherboard name: ASUS IPILP-LC
  • HP/Compaq name: Lancaster8-GL6
  • Micro-ATX: 24.4 cm (9.6 inches) x 21.8 cm (8.6 inches)
  • Intel 945GC
  • 533 MHz, 800 MHz (processor dependent)
Socket type: 775
Motherboard supports the following processor upgrades:
  • Core 2 Duo E4x00 with Dual Core technology (Conroe) up to E4400
  • Pentium E2000 series (Conroe) up to E2160
  • Pentium D 9xx with Dual Core technology (Presler) up to 960
  • Pentium 4 6x1 series (Cedar Mill) up to 661
  • Celeron 4xx series up to 440
  • Celeron D 3xx series (Cedar Mill) up to 365
  • Celeron D 3xx series (Prescott) up to 355
  • Dual channel memory architecture
  • Two 240-pin DDR2 DIMM sockets
  • Supported DIMM types:
    • PC2-3200 (400 MHz)
    • PC2-4200 (533 MHz)
    • PC2-5300 (667 MHz, runs at 533 MHz)
  • Non-ECC memory only, unbuffered
  • Supports 1 GB DDR2 DIMMs
  • Supports up to 2 GB
*Integrated video is not available if a graphics card is installed.
  • Integrated graphics using Intel GMA 950
  • Up to 256MB of system memory (with 512MB or more PC memory)
  • Also supports PCI Express x16 graphics cards*
  • Audio CODEC: Realtek ALC888
  • High Definition 6 channel audio
  • Interface: Integrated into motherboard
  • Technology: Realtek RTL8101E
  • Data transfer speeds: 10/100 Mb/s
  • Transmission standards:10-Base-T Ethernet
  • One PCI Express x16
  • One PCI Express x1
  • Two PCI
Figure 2: Back I/O panel
1 - PS/2 mouse (green)
2 - Video Graphics Adapter
3 - RJ-45 Network (LAN)
4 - Audio: Line In (light blue)
5 - Audio: Line Out (lime)
6 - Audio: Microphone (pink)
7 - USB 2.0: 4
8 - PS/2 keyboard (purple)
CAUTION: Do not change any jumper setting while the computer is on. Damage to the motherboard can result.
This motherboard has jumper to clear the Real Time Clock (RTC) RAM in CMOS.
Figure 4: Jumper location
To clear CMOS, follow these steps:
  1. To clear CMOS settings, temporarily set jumper CLRTC_HP to pins 2-4.
  2. Wait 5-10 seconds and then return the jumper to pins 4-6.
  3. When you startup the PC you will need to enter BIOS setup to reset any custom BIOS settings.
The BIOS password is used to protect BIOS settings from unwanted changes. If the BIOS password has been forgotten, disable password checking to enter setup and change or erase the password.
To erase the BIOS password follow these steps:
  1. Turn OFF the computer and unplug the power cord.
  2. Locate the jumper labeled CLPWD.
  3. Move the jumper on jumper CLPWD to pins 1-3.
  4. Plug the power cord and turn ON the computer.
  5. Hold down the F10 key during the startup process and enter BIOS setup to change or clear the password.
  6. After changing or clearing the BIOS passwords, remember to reset the jumper to pins 3-5.

HP Support forums

Find solutions and collaborate with others on the HP Support Forum
HP.comHP on FacebookHP on TwitterHP on YouTubeHP on Linked InHP on FlickrHP on Google+