Jump to content
HP Customer Support

HP and Compaq Desktop PCs Motherboard Specifications, MSI MS-7613 (Indio)

  • PrintPrint
  • Share
Figure 1: The MSI MS-7613 (Indio) motherboard
Show all | Hide all
  • Manufacturer's motherboard name: MSI MS-7613
  • HP/Compaq name: Indio-UL8E
  • Micro-ATX: 24.4 cm (9.6 inches) x 24.4 cm (9.6 inches)
  • Intel P55 Express
  • 2.5 GT/s DMI
Socket type: LGA1156
TDP: 95 watt
Motherboard supports the following processor upgrades:
  • Intel Corei7 (Lynnfield)
  • Intel Corei5 (Lynnfield)
  • Supports DDR3 DIMMs only
  • Dual channel memory architecture
  • Four DDR3 DIMM (240-pin) socket
    • PC3-10600 (DDR3-1333)
    • PC3-8500 (DDR3-1066)
  • Non-ECC memory only, unbuffered
  • Supports up to 16 GB on 64-bit PCs
  • Supports up to 4 GB* on 32-bit PCs
NOTE:32-bit PCs can only address less than 4.0 GB of memory. This motherboard is not planned for use with a 32-bit PCs.
Motherboard does not contain onboard graphics hardware to display video. A video card must be installed.
*Integrated audio is not available if a sound card is installed.
  • Audio CODEC: ALC888S
  • 6-channel high-definition audio
  • AC97: no
  • Interface: Integrated into motherboard
  • Technology: Realtek RTL8111DL
  • Data transfer speeds: up to 10/100 Mb/s
  • Transmission standards: 10-Base-T Ethernet
  • One PCI Express x16
  • Three PCI Express x1
  • One PCI Express x1 minicard socket
Figure 2: Back I/O panel
1 - USB 2.0: 2
2 - Optical SPDIF-Out
3 - IEEE 1394 (FireWire)
4 - RJ-45 Network (LAN)
5 - Audio: Center/Subwoofer (yellow orange)
6 - Audio: Rear Speaker Out (black)
7 - Audio: Side Speaker Out (gray)
8 - Audio: Line In (light blue)
9 - Audio: Line Out (lime)
10 - Audio: Microphone (pink)
11 - USB 2.0: 4
  • One CPU fan connector
  • Four DIMM sockets
  • One 24-pin ATX power connector
  • One 4-pin ATX power connector
  • Four SATA connectors
  • Six USB headers, supporting 8 USB connections
  • WLAN card LED connector
  • Clear CMOS Jumper
  • Clear BIOS Password Jumper
  • Front panel connector
  • SPDIF out connector
  • ROM Recovery
  • 1394 connector
  • Speaker
  • Front panel audio connector
  • One PCI-E x16 slot
  • Three PCI-E x 1 slots
  • One mini-PCI Express 2.0 x1 slot
  • One PC fan connector
Figure 3: layout
CAUTION: Do not change any jumper setting while the computer is on. Damage to the motherboard can result.
  1. To clear CMOS settings, set jumper JBAT1 to pins 2-3.
  2. Wait 10 seconds and then return the jumper to pins 1-2.
  3. You may now restart the computer.
The BIOS password is used to protect BIOS settings from unwanted changes. If you have forgotten your password you may use this jumper to clear the password settings.
To erase the BIOS password follow these steps:
  1. Turn OFF the computer and unplug the power cord.
  2. Locate the jumper labeled JPD1.
  3. Move the jumper on jumper JPD1 to pins 2-3.
  4. Wait approximately 10 seconds and then return the jumper to pins 1-2.
  5. Plug in the power cord and turn ON the computer.
The JSPI1 jumper is for restoring ROM.
Changing this setting *is not* recommended.