Jump to content

Specifications

  • PrintPrint

HP ProCurve 2910al-24G Switch (J9145A)

Physical specifications for the HP ProCurve 2910al-24G Switch
Feature Description
Dimensions(d)*(w)*(h)36.58 x 44.2 x 4.39 cm (14.4 x 17.4x 1.73 in) (1U height)
Weight4.95 kg (10.92 lb)
MountingMounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-24G Switch
Feature Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)
Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing
Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)
Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing
Altitude
  • up to 3 km (10,000 ft)
Acoustic
  • Power: 53.5 dB, Pressure: 39.4 dB; DIN 45635T.19 per ISO 7779
Power specifications for the HP ProCurve 2910al-24G Switch
FeatureDescription
Voltage
  • 100-127/200-240 Vac
Current
  • 1.7/0.9 A
Idle power
  • 49 W
Power consumption
  • 82 W
Frequency
  • 50/60 Hz
Maximum heat dissipation
  • 295 kJ/hr (279 BTU/hr)
Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz
NOTE:Idle power is the actual power consumption of the device with no ports connected. Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.
Technical specifications for the HP ProCurve 2910al-24G Switch
FeatureDescription
Processor
  • Dual ARM1156T2S @ 515 MHz
Memory
  • 4MB flash, 1GB flash ROM, 512MB SDRAM
  • packet buffer size: 6MB
PerformanceLatency :

  • 1000Mb : < 2.9 µs (FIFO)
  • 10 Gbps : < 1.3 µs (FIFO)


Throughput :

  • up to 95 million pps (64-byte packets)


Switching capacity :

  • 128 Gbps


Routing table size :

  • 2000 entries


MAC address table size :

  • 16,000 entries
Ports
  • 20 auto-sensing 10/100/1000 ports :
    • IEEE 802.3 Type 10Base-T
    • IEEE 802.3u Type 100Base-TX
    • IEEE 802.3ab Type 1000Base-T
    Media Type :
    • Auto-MDIX
    • Duplex: 10Base-T/100Base-TX: half or full
    • 1000Base-T: full only


  • 4 dual-personality ports :
    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)


  • 1 RJ-45 serial console port


  • Supports a maximum of four 10-GbE ports, with optional module
Management
  • HP ProCurve Manager Plus
  • HP ProCurve Manager
  • Command-line interface
  • Web browser
  • Out-of-band management (serial RS-232C)
NOTE:When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

HP ProCurve 2910al-24G-PoE+ Switch (J9146A)

Physical specifications for the HP ProCurve 2910al-24G-PoE+ Switch
Feature Description
Dimensions(d)*(w)*(h)36.58 x 44.2 x 4.39 cm (14.4 x 17.4 x 1.73 in) (1U height)
Weight5.6 kg (12.34 lb)
MountingMounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-24G-PoE+ Switch
Feature Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)
Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing
Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)
Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing
Altitude
  • up to 3 km (10,000 ft)
Acoustic
  • Power: 51.5 dB, Pressure: 38.1 dB; DIN 45635T.19 per ISO 7779
Power specifications for the HP ProCurve 2910al-24G-PoE+ Switch
FeatureDescription
Voltage
  • 100-127/200-240 Vac
Current
  • 6.1/3.1 A
Idle power
  • 65 W
Power consumption
  • 490 W
Frequency
  • 50/60 Hz
Maximum heat dissipation
  • 472 kJ/hr (447 BTU/hr), max. using PoE+
Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz
NOTE:Idle power is the actual power consumption of the device with no ports connected. Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.
Technical specifications for the HP ProCurve 2910al-24G Switch
FeatureDescription
Processor
  • Dual ARM1156T2S @ 515 MHz
Memory
  • 4MB flash ROM, 1GB flash, 512MB SDRAM
  • packet buffer size: 6MB
PerformanceLatency :

  • 1000Mb : < 2.9 µs (FIFO)
  • 10 Gbps : < 1.3 µs (FIFO)


Throughput :

  • up to 95 million pps (64-byte packets)


Switching capacity :

  • 128 Gbps


Routing table size :

  • 2000 entries


MAC address table size :

  • 16,000 entries
Ports
  • 20 auto-sensing 10/100/1000 ports :
    • IEEE 802.3 Type 10Base-T
    • IEEE 802.3u Type 100Base-TX
    • IEEE 802.3ab Type 1000Base-T
    Media Type :
    • Auto-MDIX
    • Duplex: 10Base-T/100Base-TX: half or full
    • 1000Base-T: full only


  • 4 dual-personality ports :
    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)


  • 1 RJ-45 serial console port


  • Supports a maximum of four 10-GbE ports, with optional module
Management
  • HP ProCurve Manager Plus
  • HP ProCurve Manager
  • Command-line interface
  • Web browser
  • Out-of-band management (serial RS-232C)
NOTE:When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

HP ProCurve 2910al-48G Switch (J9147A)

Physical specifications for the HP ProCurve 2910al-48G Switch
Feature Description
Dimensions(d)*(w)*(h)36.58 x 44.25 x 4.4 cm (14.4 x 17.42 x 1.73 in) (1U height)
Weight5.08 kg (11.2 lb)
MountingMounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-48G Switch
Feature Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)
Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing
Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)
Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing
Altitude
  • up to 3 km (10,000 ft)
Acoustic
  • Power: 53.5 dB, Pressure: 39.4 dB; DIN 45635T.19 per ISO 7779
Power specifications for the HP ProCurve 2910al-48G Switch
FeatureDescription
Voltage
  • 100-127/200-240 Vac
Current
  • 2.1/1.1 A
Idle power
  • 64 W
Power consumption
  • 105 W
Frequency
  • 50/60 Hz
Maximum heat dissipation
  • 376 kJ/hr (356 BTU/hr)
Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz
NOTE:Idle power is the actual power consumption of the device with no ports connected. Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.
Technical specifications for the HP ProCurve 2910al-48G Switch
FeatureDescription
Processor
  • Dual ARM1156T2S @ 515 MHz
Memory
  • 4MB flash, 1GB flash ROM, 512MB SDRAM
  • packet buffer size: 6MB
PerformanceLatency :

  • 1000Mb : < 2.9 µs (FIFO)
  • 10 Gbps : < 1.3 µs (FIFO)


Throughput :

  • up to 131 million pps


Switching capacity :

  • 176 Gbps


Routing table size :

  • 2000 entries


MAC address table size :

  • 16,000 entries
Ports
  • 44 auto-sensing 10/100/1000 ports :
    • IEEE 802.3 Type 10Base-T
    • IEEE 802.3u Type 100Base-TX
    • IEEE 802.3ab Type 1000Base-T
    Media Type :
    • Auto-MDIX
    • Duplex: 10Base-T/100Base-TX: half or full
    • 1000Base-T: full only


  • 4 dual-personality ports :
    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)


  • 1 RJ-45 serial console port


  • Supports a maximum of four 10-GbE ports, with optional module
Management
  • HP ProCurve Manager Plus
  • HP ProCurve Manager
  • Command-line interface
  • Web browser
  • Out-of-band management (serial RS-232C)
NOTE:When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

HP ProCurve 2910al-48G-PoE+ Switch (J9148A)

Physical specifications for the HP ProCurve 2910al-48G-PoE+ Switch
Feature Description
Dimensions(d)*(w)*(h)36.58 x 44.25 x 4.39 cm (14.4 x 17.42x 1.73 in) (1U height)
Weight5.88 kg (12.96 lb)
MountingMounts in an EIA-standard 19 inch telco rack or equipment cabinet ; horizontal surface mounting only
Environmental specifications for the HP ProCurve 2910al-48G-PoE+ Switch
Feature Description
Operating temperature
  • 0ºC to 55ºC (32ºF to 131ºF)
Operating relative humidity
  • 15% to 95% @ 40ºC (104ºF), non-condensing
Non-operating/ Storage temperature
  • -40ºC to 70ºC (-40ºF to 158ºF)
Non-operating/ Storage relative humidity
  • 15% to 95% @ 65ºC (149ºF), non-condensing
Altitude
  • up to 3 km (10,000 ft)
Acoustic
  • Power: 51.5 dB, Pressure: 38.1 dB; DIN 45635T.19 per ISO 7779
Power specifications for the HP ProCurve 2910al-48G-PoE+ Switch
FeatureDescription
Voltage
  • 100-127/200-240 Vac
Current
  • 6.4/3.2 A
Idle power
  • 89 W
Power consumption
  • 556 W
Frequency
  • 50/60 Hz
Maximum heat dissipation
  • 704 kJ/hr (667 BTU/hr)
Description
  • The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and frequency either 50 or 60 Hz
NOTE:Idle power is the actual power consumption of the device with no ports connected. Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.
Technical specifications for the HP ProCurve 2910al-48G-PoE+ Switch
FeatureDescription
Processor
  • Dual ARM1156T2S @ 515 MHz
Memory
  • 4MB flash ROM, 1GB flash, 512MB SDRAM
  • packet buffer size: 6MB
PerformanceLatency :

  • 1000Mb : < 2.9 µs (FIFO)
  • 10 Gbps : < 1.3 µs (FIFO)


Throughput :

  • up to 131 million pps


Switching capacity :

  • 176 Gbps


Routing table size :

  • 2000 entries


MAC address table size :

  • 16,000 entries
Ports
  • 44 auto-sensing 10/100/1000 ports :
    • IEEE 802.3 Type 10Base-T
    • IEEE 802.3u Type 100Base-TX
    • IEEE 802.3ab Type 1000Base-T
    Media Type :
    • Auto-MDIX
    • Duplex: 10Base-T/100Base-TX: half or full
    • 1000Base-T: full only


  • 4 dual-personality ports :
    • Each port can be used as either an RJ-45 10/100/1000 port or as a mini-GBIC slot (for use with mini-GBIC transceivers)


  • 1 RJ-45 serial console port


  • Supports a maximum of four 10-GbE ports, with optional module
Management
  • HP ProCurve Manager Plus
  • HP ProCurve Manager
  • Command-line interface
  • Web browser
  • Out-of-band management (serial RS-232C)
NOTE:When using mini-GBICs with this product, mini-GBICs with revision B or later (product number ends with the letter B or later, e.g., J4858B, J4859C) are required.

Safety and emission certificates

FeatureDescription
Safety
  • EN 60950/IEC 60950
  • CAN/CSA 22.2 No. 60950
  • EN 60825
  • UL 60950
Emissions
  • FCC part 15 Class A
  • EN 55022/CISPR-22 Class A
  • VCCI Class A
ImmunityEN :

  • EN 55024, CISPR 24


ESD :

  • IEC 61000-4-2; 4 kV CD, 8 kV AD


Radiated :

  • IEC 61000-4-3; 3 V/m


EFT/Burst :

  • IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)


Surge :

  • IEC 61000-4-5; 1 kV / 2 kV AC, 1 kV signal, 0.5 kV DC


Conducted :

  • IEC 61000-4-6; 3 V


Power frequency magnetic field :

  • IEC 61000-4-8; 1 A/m


Voltage dips and interruptions :

  • IEC 61000-4-11; > 95% reductions, 0.5 period; 30% reduction, 25 periods


Harmonics :

  • IEC 61000-3-2


Flicker :

  • IEC 61000-3-3

Standards and protocols

FeatureDescription
Device management
  • RFC 1591 DNS (client)
  • HTML and telnet management
General protocols
  • IEEE 802.1D MAC Bridges
  • IEEE 802.1p Priority
  • IEEE 802.1Q VLANs
  • IEEE 802.1s Multiple Spanning Trees
  • IEEE 802.1v VLAN classification by Protocol and Port
  • IEEE 802.1w Rapid Reconfiguration of Spanning Tree
  • IEEE 802.3ad Link Aggregation Control Protocol (LACP)
  • IEEE 802.3x Flow Control
  • RFC 768 UDP
  • RFC 783 TFTP Protocol (revision 2)
  • RFC 792 ICMP
  • RFC 793 TCP
  • RFC 826 ARP
  • RFC 854 TELNET
  • RFC 868 Time Protocol
  • RFC 951 BOOTP
  • RFC 1058 RIPv1
  • RFC 1350 TFTP Protocol (revision 2)
  • RFC 2030 Simple Network Time Protocol (SNTP) v4
  • RFC 2131 DHCP
  • RFC 2453 RIPv2
  • RFC 3046 DHCP Relay Agent Information Option
IP multicast
  • RFC 3376 IGMPv3 (host joins only)
IPv6
  • RFC 1981 IPv6 Path MTU Discovery
  • RFC 2460 IPv6 Specification
  • RFC 2710 Multicast Listener Discovery (MLD) for IPv6
  • RFC 2925 Remote Operations MIB (Ping only)
  • RFC 3019 MLDv1 MIB
  • RFC 3315 DHCPv6 (client only)
  • RFC 3513 IPv6 Addressing Architecture
  • RFC 3596 DNS Extension for IPv6
  • RFC 3810 MLDv2 (host joins only)
  • RFC 4022 MIB for TCP
  • RFC 4113 MIB for UDP
  • RFC 4251 SSHv6 Architecture
  • RFC 4252 SSHv6 Authentication
  • RFC 4253 SSHv6 Transport Layer
  • RFC 4254 SSHv6 Connection
  • RFC 4293 MIB for IP
  • RFC 4419 Key Exchange for SSH
  • RFC 4443 ICMPv6
  • RFC 4541 IGMP & MLD Snooping Switch
  • RFC 4861 IPv6 Neighbor Discovery
  • RFC 4862 IPv6 Stateless Address Auto-configuration
MIBs
  • RFC 1213 MIB II
  • RFC 1493 Bridge MIB
  • RFC 1724 RIPv2 MIB
  • RFC 2021 RMONv2 MIB
  • RFC 2613 SMON MIB
  • RFC 2618 RADIUS Client MIB
  • RFC 2620 RADIUS Accounting MIB
  • RFC 2665 Ethernet-Like-MIB
  • RFC 2668 802.3 MAU MIB
  • RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
  • RFC 2737 Entity MIB (Version 2)
  • RFC 2863 The Interfaces Group MIB
Network management
  • IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
  • RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events)
  • RFC 3176 sFlow
  • ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED)
  • SNMPv1/v2c/v3
  • XRMON
QoS/Cos
  • RFC 2474 DiffServ Precedence, including 8 queues/port
  • RFC 2597 DiffServ Assured Forwarding (AF)
  • RFC 2598 DiffServ Expedited Forwarding (EF)
  • Ingress Rate Limiting
Security
  • IEEE 802.1X Port Based Network Access Control
  • RFC 1492 TACACS+
  • RFC 2138 RADIUS Authentication
  • RFC 2866 RADIUS Accounting
  • Secure Sockets Layer (SSL)

Related support links

HP Support forums

Find solutions and collaborate with others on the HP Support Forum
HP on YouTube