Jump to content

HP Officejet 4500 Wireless All-in-One Printer - G510n support

Replacing Cartridges for HP Officejet 4500 All-in-One Printer Series

  • PrintPrint
This document is for the HP Officejet 4500 All-in-One Printer Series.
This document contains steps for replacing the cartridges.

Cartridges types

Consult the following table to identify the correct cartridges for your area.
Country/RegionBlack cartridgeTri-color cartridge
Latin AmericaHP 675 BlackHP 675 Tri-color
VietnamHP 675 BlackHP 675 Tri-color
HP 703 Tri-color
PhilippinesHP 703 Black
To purchase cartridges or check cartridge compatibility for your printer, go to HP Home & Home Office Store (US only), and then click Ink Toner & Paper.
If you are located outside of the US, follow these steps to purchase cartridges using HP SureSupply.
  1. Scroll to the bottom of the page and make sure that the country/region location is correct.
Genuine HP cartridges can also be purchased from other retailers.

Replacing cartridges

Follow these steps in the order presented to replace the cartridges.

Video of replacing the cartridges

The following video demonstrates how to replace a cartridge.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
CAUTION: Do not leave the cartridge outside the product for an extended period. This can result in damage to the product and the cartridge. Have a new cartridge available before removing the old cartridge.

Step one: Remove the old cartridges

  1. Press the power button () to turn on the product.
    CAUTION:If the product is off when the cartridge door is opened, the product will not release the cartridges.
  2. Open the front access door. The carriage moves to the far right side of the product.
    Figure 1: Open the front access door
    IIustration of opening the front access door
  3. Wait until the carriage is idle and silent, and then lightly press down on the cartridge to release it.
    • To replace the tri-color cartridge, remove the cartridge from the slot on the left.
    • To replace the black cartridge, remove the cartridge from the slot on the right.
      Figure 2: Remove the black cartridge
      Illustration of removing the black cartridge.
  4. Pull the cartridge toward you out of its slot.

Step two: Install the new cartridges

  1. Remove the new cartridge from its packaging. Be careful to touch only the black plastic.
  2. Gently remove the plastic tape by pulling the pink pull tab.
    Figure 3: Remove the tape
    Illustration of removing the tape
    1 - Copper-colored contacts
    2 - Plastic tape with pink pull tab (must be removed before installing)
    3 - Ink nozzles under tape
    CAUTION:Do not touch the copper-colored contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections.
    Figure 4: Do not touch the contacts or ink nozzles
    Illustration of the contacts and ink nozzles
  3. Hold the cartridge with the HP logo on top, and insert the new cartridge into the empty cartridge slot. Make sure you push the cartridge in firmly until it snaps into place.
    Figure 5: Insert the cartridge into the empty slot
    Illustration of inserting the cartridge into the empty slot
    • If you are installing the tri-color cartridge, slide it into the left slot.
    • If you are installing a black cartridge, slide it into the right slot.
  4. Close the front access door.

Step three: Load plain paper

Follow these steps to load plain paper into your product. If you already loaded plain paper in the product, skip to the next step.
  1. Pull out the tray extender.
    Figure 6: Pull out the tray extender
    Illustration of pulling out the tray extender
  2. Insert the paper stack into the input tray with the short edge forward and print side down.
    NOTE:Do not load paper while the device is printing.
  3. Adjust the paper width guide so it rests against the stack of paper.
    Figure 7: Adjust the paper width guide
    Illustration of adjusting the paper width guide

Step four: Align the product

  1. When prompted after loading the paper, press OK on the control panel to begin the alignment process. The product prints an alignment page.
    Figure 8: Alignment page
    Illustration of  alignment page
  2. Open the scanner lid, and then place the printed alignment page face down on the scanner glass.
    Figure 9: Open the scanner lid and place the page on the scanner glass
    Illustration of opening the scanner lid and placing the page on the scanner glass
  3. Close the scanner lid.
  4. Press OK. The product scans the alignment page, completing the alignment.
HP Officejet 4500 Wireless All-in-One Printer - G510n

HP Support forums

Find solutions and collaborate with others on the HP Support Forum
HP.comHP on FacebookHP on TwitterHP on YouTubeHP on Linked InHP on FlickrHP on Google+