Jump to content

HP LaserJet Pro CP1525nw Color Printer support

Setting Up the Printer for a Wired or Wireless Network for the HP LaserJet Pro CP1525n and CP1525nw Color Printers

  • PrintPrint

Introduction

This document explains how to install the print drivers and other software for your HP product to use it on a wireless or wired (Ethernet) network. The wireless setup instructions are specific to a wireless network that uses an access point
A device, such as a wireless router, that allows wireless-capable devices (like your HP product) to connect to your wireless network.
(infrastructure network). This document also explains how to change your product from a USB install to a network install.
NOTE:If you have more than one computer on the network, install the product software on each computer that you plan to share with the HP product.
Follow these steps for the Windows XP operating system. Next, choose your connection type.
Follow these steps to install your HP product over a wired (Ethernet) network.
Important: You must follow these steps in the order presented.

Step one: Check requirements

Make sure you have the following items:
  • One of the following types of wired access points or routers: Ethernet router, switch, hub, or wireless router with Ethernet ports
  • A computer that connects to the wired access point or router
  • A Category 5 Ethernet cable to use for the HP product. (Do not use a standard telephone cable.)
    Figure 1: Cable comparison
    Ethernet cable and telephone cable
    1 - Ethernet cable
    2 - Telephone cable (do not use)
    Although an Ethernet cable looks similar to standard telephone cable, each has a different plug and a different number of wires. The plug on an Ethernet cable (also called an RJ-45 connector) is wide, thick, and always has eight wires. The plug on a telephone cable is narrower and has between two and six wires.
  • A network that uses one or more of the following protocols:
    • TCP/IP (IPv4 or IPv6)
    • Port 9100
    • LPR
    • DHCP
    • AutoIP
    • SNMP
    • Bonjour
    • SLP
    • WSD
    • NBNS
    • LLMNR

Step two: Change from USB connection to Ethernet connection

If you previously installed the software for a USB connection and now want to change to an Ethernet connection, follow these instructions to remove the USB installation before continuing.

Step three: Connect the HP printer to the network

Follow these steps to connect the product to the wired network.
  1. Remove any plug or protective cover from the Ethernet port on the back of the product.
    Figure 2: Remove plug
    Image: Remove the plug.
  2. Connect the Ethernet cable to the Ethernet port on the product. Then connect the other end of the cable to an available port on the wired access point or router.
    Figure 3: Connect the Ethernet cable
    Image: Connect the Ethernet cable.
  3. Wait 60 seconds before continuing. During this time, the network recognizes the product and assigns an IP address or host name for the product.
  4. On the product control panel, press OK.
  5. Print a Configuration Report.
    1. Load plain white paper into tray 1.
    2. Press the Right arrow button () to select Reports, and then press OK.
    3. Press the Right arrow button () to select Config report, and then press OK.
  6. Make note of the product IP address on the Configuration Report for future reference.

Step four: Decide whether to install with the product CD or download the software

Don’t worry if you don’t have the product CD! You can download the most current software available for your product from the HP Web site at no cost. The following information might help you decide which installation method to use:
CDDownload
For a new product:CD installation is a quick and easy method.If you do not have a CD, you can download the software you need.
For an older product:CD installation might not work if you are installing the product on a computer running a newer operating system that released AFTER the HP product released.Downloading the software provides the best results for your older product. Even though it takes more time than using the CD, downloading the latest software can help you avoid installation issues.

Downloading is the recommended method if your computer operating system released after the HP product released.
About the software:The software on the CD is current to the date of the product release.The software that you can download from the HP Web site is the most current software available for your product. HP often updates software and drivers AFTER the product and CD release to the market.

Step five: Install the software

When you are ready to begin, follow the instructions for the installation method that you want to use (CD or download). During the installation, choose the option for the network type of connection, not the USB option.
Important: If you get any firewall messages during installation, click unblock, accept, continue, yes, allow, or permit, or the installation fails.
Follow these steps to download and install the software.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you will be prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 4: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Follow these steps to install the software with the product CD.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you are prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Insert the product CD into the CD drive of the computer, and then wait a few seconds for the software installer to start.
    If the installer does not start automatically, follow these steps to start it:
    Click Start (), click My Computer, and then double-click the CD drive.
    NOTE:If the User Account Control screen opens, click Allow to continue.
  2. Follow the on-screen instructions to start the installation.
  3. In the Software to Install window, you can choose to install the recommended software or the minimum software.
    • Recommended: Click Next to install the recommended software. The recommended software provides full product functionality and includes valuable software, such as HP Toolbox and Help and Learn Center. HP designed this type of installation to work for most users.
    • Minimum: Click Click here for more install options to install the minimum software. The minimum software contains only the print driver. Install the minimum software if the computer is low on hard disk space.
  4. When prompted to select a connection type, select the Network type, not the USB type. The USB cable is for the installation procedure only. (The installer prompts you when to connect and disconnect the USB cable.)
  5. Click Next.
  6. Follow the on-screen instructions to finish installing the software.
If you have a wireless-capable HP product and want to install it on a wireless network, follow these steps.
Important: You must follow these steps in the order presented.

Step one: Gather the required network setup items

You must have the following items before you install the HP product on the wireless network:
Do not worry if you do not have all of the items yet! The HP Print and Scan Doctor
The HP Print and Scan Doctor is an automated tool designed to help you gather network information.
can help you gather some of these items.
  • Network name: The network name is the SSID
  • WEP key or WPA security passphrase
  • A computer that is connected to the wireless network
  • Internet access: HP recommends broadband Internet access such as cable or DSL
    NOTE:Internet access is not required for you to install your printer with a wireless connection. However, you do need Internet access to use Web Services or get product updates.
  • Your wireless-capable HP printer: Place it close to the computer during the installation procedure
  • A USB cable (used only during installation). Do not connect the cable now
HP designed a quick and easy tool that diagnoses and resolves many printing, scanning, and connectivity problems: The HP Print and Scan Doctor. If you have difficulty gathering your network information, try using the HP Print and Scan Doctor to retrieve your network name and password.
NOTE:The HP Print and Scan Doctor might not be available for all HP products, particularly older products. It is available for most products, however, and in most languages. This tool is available only for Windows operating systems. The tool is not available for Mac OS operating systems.
Follow these steps to download and run the HP Print and Scan Doctor, and then locate your network login information.
  1. Click the following link to download the HP Print and Scan Doctor.
  2. Make sure your computer meets the system requirements, and then click Download.
  3. When the Security Warning dialog box opens, choose one of the following methods to download the utility.
      1. In the Security Warning dialog box, click Run.
      2. When the Download Complete dialog box opens, click Run, and then click Run again on the Security Warning dialog box. The Print and Scan Doctor opens.
      1. In the Security Warning dialog box, click Save.
      2. When the Save As window opens, browse to your Desktop, and then click Save.
      3. When the download is complete, browse to where you saved the file, and then double-click the file to run the utility. The Print and Scan Doctor opens.
  4. On the Menu bar in the Print and Scan Doctor window, click Help.
  5. Click Show Advanced Info.
  6. Click Show Wireless Info.
  7. Under the Wireless Settings pane, identify the name of your network under SSID, and then identify the Network Key next to it in the list.

Step two: Prepare for installation

  1. Make sure that the HP product, access point, and computer are all turned on, and that the computer is connected to the wireless network.
  2. Exit all applications running on your computer.
  3. Disconnect any USB or Ethernet cable that is connected to the HP product.
  4. If you previously installed the software for a USB connection and now want to change to a wireless network connection, follow these instructions to remove the USB installation before continuing.

Step three: Connect to the wireless network

Use one of the following methods to connect to the wireless network.
Follow these steps to connect your printer to the wireless network using WPS.
Video of connecting your wireless printer to a wireless network using WPS
The following video demonstrates how to use Wi-Fi Protected Setup to connect your printer to a wireless network.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
If your wireless router supports Wi-Fi Protected Setup (WPS), this is the simplest way to set up the product on a wireless network.
NOTE:This method requires a WPS-enabled wireless router to connect to the product.
  1. Press the WPS button on your wireless router.
  2. On the control panel, press and hold the Wireless button () for two seconds. Release the button when the wireless light starts blinking.
  3. Wait up to two minutes while the product establishes a network connection with the wireless router.
    NOTE:If the WiFi-Protected Setup (WPS) method is not successful, try using the product control panel, or the USB cable connection method.
If your wireless router does not support WiFi-Protected Setup (WPS), use one of the following options to connect the product to your wireless network.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, follow these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select Pushbutton, and then follow the on-screen instructions to connect to the wireless network.
    NOTE:Establishing the wireless connection can take a few minutes.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, complete these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select PIN. The product generates a unique PIN.
  4. Type the unique PIN into the wireless router's setup screen, and then click Save or Apply.
    NOTE:Establishing the wireless connection can take a few minutes.
If your wireless router does not support WiFi-Protected Setup (WPS), you can use this method to set up the product on a wireless network. Using a USB cable to transfer settings makes setting up a wireless connection easier. After the setup is complete, disconnect the USB cable.
Video of connecting your wireless printer to a wireless network with a USB cable
The following video demonstrates how to connect your wireless HP printer to a wireless network through a USB cable.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
  1. Insert the software CD into the CD drive.
  2. Follow the on-screen instructions. When prompted, select the Connect through a wireless network option.
  3. Connect the USB cable () to the product and the computer when prompted.
    CAUTION:Do not connect the USB cable until the installation program prompts you.
  4. When the installation is complete, print a Configuration Report to make sure that the product has an SSID name. Follow these steps to print a configuration report:
    1. Load plain white paper into tray 1.
    2. On the product control panel, press OK, and then press OK again to select Reports.
    3. Press the Right Arrow button ( ) to scroll to and select Config Report.
  5. When the Configuration Report prints, disconnect the USB cable () from the product.
    You have completed the software installation. Do not perform any more steps in this document.

Step four: Decide whether to install with the product CD or download the software

Don’t worry if you don’t have the printer CD! You can download the most current software available for your printer from the HP website at no cost. The following information might help you decide which installation method to use:
    For a new printer:CD installation is a quick and easy method.
    For an older printer:CD installation might not work if you are installing the printer on a computer running a newer operating system that released AFTER the HP printer released.

    For example, Windows Vista released in 2007. If HP manufactured your printer prior to that year, the CD that came with the printer might not work correctly on a computer running Vista.
    About the software:The software on the CD is current to the date of the printer release.
    For a new printer:If you do not have a CD, you can download the software you need.
    For an older printer:Downloading the software provides the best results for your older printer. Even though it takes more time than using the CD, downloading the latest software can help you avoid installation issues.

    Downloading is the recommended method if your computer operating system released after the HP printer released.
    About the software:The software you can download from the HP website is most current software available for your printer. HP often updates software and drivers after the printer and CD release to the market.

Step five: Install the product software

To install the product on the wireless network, follow the steps for the method that you want to use (CD or download). Repeat the steps to install the software on each computer that will use the product wirelessly over the same network.
Important: If you get any firewall messages during installation, click unblock, accept, continue, yes, allow, or permit, or the installation will fail.
Follow these steps to download and install the software.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you will be prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 5: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Follow these steps to install the software with the product CD.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you are prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Insert the product CD into the CD drive of the computer, and then wait a few seconds for the software installer to start.
    If the installer does not start automatically, follow these steps to start it:
    Click Start (), click My Computer, and then double-click the CD drive.
    NOTE:If the User Account Control screen opens, click Allow to continue.
  2. Follow the on-screen instructions to start the installation.
  3. In the Software to Install window, you can choose to install the recommended software or the minimum software.
    • Recommended: Click Next to install the recommended software. The recommended software provides full product functionality and includes valuable software, such as HP ToolboxFX and Help and Learn Center. HP designed this type of installation to work for most users.
    • Minimum: Click Click here for more install options to install the minimum software. The minimum software contains only the print driver. Install the minimum software if the computer is low on hard disk space.
  4. When prompted to choose a connection type, select the Network type, not the USB type. The USB cable is for the installation procedure only. (The installer prompts you when to connect and disconnect the USB cable.)
  5. Click Next.
  6. Follow the on-screen instructions to finish installing the software.
Follow these steps for the Windows Vista operating system. Next, choose your connection type.
If you want to install your HP product over a wired (Ethernet) network, follow these steps.
Important: You must follow these steps in the order presented.

Step one: Check requirements

Make sure you have the following items:
  • One of the following types of wired access points or routers: Ethernet router, switch, hub, or wireless router with Ethernet ports
  • A computer that connects to the wired access point or router
  • A Category 5 Ethernet cable to use for the HP product. (Do not use a standard telephone cable.)
    Figure 6: Cable comparison
    Ethernet cable and telephone cable
    1 - Ethernet cable
    2 - Telephone cable (do not use)
    Although an Ethernet cable looks similar to standard telephone cable, each has a different plug and a different number of wires. The plug on an Ethernet cable (also called an RJ-45 connector) is wide, thick, and always has eight wires. The plug on a telephone cable is narrower and has between two and six wires.
  • A network that uses one or more of the following protocols:
    • TCP/IP (IPv4 or IPv6)
    • Port 9100
    • LPR
    • DHCP
    • AutoIP
    • SNMP
    • Bonjour
    • SLP
    • WSD
    • NBNS
    • LLMNR

Step two: Change from USB connection to Ethernet connection

If you previously installed the software for a USB connection and now want to change to an Ethernet connection, follow these instructions to remove the USB installation before continuing.

Step three: Connect the HP printer to the network

Follow these steps to connect the product to the wired network.
  1. Remove any plug or protective cover from the Ethernet port on the back of the product.
    Figure 7: Remove plug
    Image: Remove the plug.
  2. Connect the Ethernet cable to the Ethernet port on the product. Then connect the other end of the cable to an available port on the wired access point or router.
    Figure 8: Connect the Ethernet cable
    Image: Connect the Ethernet cable.
  3. Wait 60 seconds before continuing. During this time, the network recognizes the product and assigns an IP address or host name for the product.
  4. On the product control panel, press OK.
  5. Print a Configuration Report.
    1. Load plain white paper into tray 1.
    2. Press the Right arrow button () to select Reports, and then press OK.
    3. Press the Right arrow button () to select Config report, and then press OK.
  6. Make note of the product IP address on the Configuration Report for future reference.

Step four: Decide whether to install with the product CD or download the software

Don’t worry if you don’t have the product CD! You can download the most current software available for your product from the HP Web site at no cost. The following information might help you decide which installation method to use:
CDDownload
For a new product:CD installation is a quick and easy method.If you do not have a CD, you can download the software you need.
For an older product:CD installation might not work if you are installing the product on a computer running a newer operating system that released AFTER the HP product released.Downloading the software provides the best results for your older product. Even though it takes more time than using the CD, downloading the latest software can help you avoid installation issues.

Downloading is the recommended method if your computer operating system released after the HP product released.
About the software:The software on the CD is current to the date of the product release.The software that you can download from the HP Web site is the most current software available for your product. HP often updates software and drivers AFTER the product and CD release to the market.

Step five: Install the software

When you are ready to begin, follow the instructions for the installation method that you want to use (CD or download). During the installation, choose the option for the network type of connection, not the USB option.
IMPORTANT: If you get any firewall messages during installation, click unblock, accept, continue, yes, allow, or permit, or the installation fails.
Follow these steps to download and install the software.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you will be prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 9: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Follow these steps to install the software with the product CD.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you will be prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Press the Power switch or button to turn on the product.
  2. Insert the product CD into the CD drive of the computer, and then wait a few seconds for the software installer to begin.
    If the installer does not begin automatically, click the Windows icon (), click Computer, and then double-click the CD drive.
    NOTE:If the User Account Control screen opens, click Allow to continue.
  3. Follow the on-screen instructions to start the installation.
  4. In the Software to Install window, you can choose to install the recommended software or the minimum software.
    • Recommended: Click Next to install the recommended software. The recommended software provides full product functionality and includes valuable software, such as HP Toolbox and Help and Learn Center. HP designed this type of installation to work for most users.
    • Minimum: Click Click here for more install options to install the minimum software. The minimum software contains only the print driver. Install the minimum software if the computer is low on hard disk space.
  5. When prompted to choose a connection type, select the Network type, not the USB type. The USB cable is for the installation procedure only. (The installer prompts you when to connect and disconnect the USB cable.)
  6. Click Next.
      Important: At this point, the installer searches, but does not find the product because it is not yet connected. This is expected behavior and does not indicate a problem with the setup. Click Next again to continue with the installation.
  7. Follow the on-screen instructions to finish installing the software.
    NOTE:If you have previously installed the software and are changing the connection type from USB to Ethernet, click Add a device when the Uninstall the software or Add a device window opens.
    Important: The installer might ask if you want to check online for the latest installation updates for your product. For the best installation results, HP recommends that you click “Yes” to let the installer check for updates and download them for you.
If you have a wireless-capable HP product and want to install it on a wireless network, follow these steps.
Important: You must follow these steps in the order presented.

Step one: Gather the required network setup items

You must have the following items before you install the HP product on the wireless network:
Do not worry if you do not have all of the items yet! The HP Print and Scan Doctor
The HP Print and Scan Doctor is an automated tool designed to help you gather network information.
can help you gather some of these items.
  • Network name: The network name is the SSID
  • WEP key or WPA security passphrase
  • A computer that is connected to the wireless network
  • Internet access: HP recommends broadband Internet access such as cable or DSL
    NOTE:Internet access is not required for you to install your printer with a wireless connection. However, you do need Internet access to use Web Services or get product updates.
  • Your wireless-capable HP printer: Place it close to the computer during the installation procedure
  • A USB cable (used only during installation). Do not connect the cable now
HP designed a quick and easy tool that diagnoses and resolves many printing, scanning, and connectivity problems: The HP Print and Scan Doctor. If you have difficulty gathering your network information, try using the HP Print and Scan Doctor to retrieve your network name and password.
NOTE:The HP Print and Scan Doctor might not be available for all HP products, particularly older products. It is available for most products, however, and in most languages. This tool is available only for Windows operating systems. The tool is not available for Mac OS operating systems.
Follow these steps to download and run the HP Print and Scan Doctor, and then locate your network login information.
  1. Click the following link to download the HP Print and Scan Doctor.
  2. Make sure your computer meets the system requirements, and then click Download.
  3. When the Security Warning dialog box opens, choose one of the following methods to download the utility.
      1. In the Security Warning dialog box, click Run.
      2. When the Download Complete dialog box opens, click Run, and then click Run again on the Security Warning dialog box. The Print and Scan Doctor opens.
      1. In the Security Warning dialog box, click Save.
      2. When the Save As window opens, browse to your Desktop, and then click Save.
      3. When the download is complete, browse to where you saved the file, and then double-click the file to run the utility. The Print and Scan Doctor opens.
  4. On the Menu bar in the Print and Scan Doctor window, click Help.
  5. Click Show Advanced Info.
  6. Click Show Wireless Info.
  7. Under the Wireless Settings pane, identify the name of your network under SSID, and then identify the Network Key next to it in the list.

Step two: Prepare for installation

  1. Make sure that the HP product, access point, and computer are all turned on, and that the computer is connected to the wireless network.
  2. Exit all applications running on your computer.
  3. Disconnect any USB or Ethernet cable that is connected to the HP product.
  4. If you previously installed the software for a USB connection and now want to change to a wireless network connection, follow these instructions to remove the USB installation before continuing.

Step three: Connect to the wireless network

Use one of the following methods to connect to the wireless network.
Follow these steps to connect your printer to the wireless network using WPS.
Video of connecting your wireless printer to a wireless network using WPS
The following video demonstrates how to use Wi-Fi Protected Setup to connect your printer to a wireless network.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
If your wireless router supports Wi-Fi Protected Setup (WPS), this is the simplest way to set up the product on a wireless network.
NOTE:This method requires a WPS-enabled wireless router to connect to the product.
  1. Press the WPS button on your wireless router.
  2. On the control panel, press and hold the Wireless button () for two seconds. Release the button when the wireless light starts blinking.
  3. Wait up to two minutes while the product establishes a network connection with the wireless router.
    NOTE:If the WiFi-Protected Setup (WPS) method is not successful, try using the product control panel, or the USB cable connection method.
If your wireless router does not support WiFi-Protected Setup (WPS), use one of the following options to connect the product to your wireless network.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, follow these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select Pushbutton, and then follow the on-screen instructions to connect to the wireless network.
    NOTE:Establishing the wireless connection can take a few minutes.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, complete these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select PIN. The product generates a unique PIN.
  4. Type the unique PIN into the wireless router's setup screen, and then click Save or Apply.
    NOTE:Establishing the wireless connection can take a few minutes.
If your wireless router does not support WiFi-Protected Setup (WPS), you can use this method to set up the product on a wireless network. Using a USB cable to transfer settings makes setting up a wireless connection easier. After the setup is complete, disconnect the USB cable.
Video of connecting your wireless printer to a wireless network with a USB cable
The following video demonstrates how to connect your wireless HP printer to a wireless network through a USB cable.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
  1. Insert the software CD into the CD drive.
  2. Follow the on-screen instructions. When prompted, select the Connect through a wireless network option.
  3. Connect the USB cable () to the product and the computer when prompted.
    CAUTION:Do not connect the USB cable until the installation program prompts you.
  4. When the installation is complete, print a Configuration Report to make sure that the product has an SSID name. Follow these steps to print a configuration report:
    1. Load plain white paper into tray 1.
    2. On the product control panel, press OK, and then press OK again to select Reports.
    3. Press the Right Arrow button ( ) to scroll to and select Config Report.
  5. When the Configuration Report prints, disconnect the USB cable () from the product.
    You have completed the software installation. Do not perform any more steps in this document.

Step four: Decide whether to install with the product CD or download the software

Don’t worry if you don’t have the printer CD! You can download the most current software available for your printer from the HP website at no cost. The following information might help you decide which installation method to use:
    For a new printer:CD installation is a quick and easy method.
    For an older printer:CD installation might not work if you are installing the printer on a computer running a newer operating system that released AFTER the HP printer released.

    For example, Windows Vista released in 2007. If HP manufactured your printer prior to that year, the CD that came with the printer might not work correctly on a computer running Vista.
    About the software:The software on the CD is current to the date of the printer release.
    For a new printer:If you do not have a CD, you can download the software you need.
    For an older printer:Downloading the software provides the best results for your older printer. Even though it takes more time than using the CD, downloading the latest software can help you avoid installation issues.

    Downloading is the recommended method if your computer operating system released after the HP printer released.
    About the software:The software you can download from the HP website is most current software available for your printer. HP often updates software and drivers after the printer and CD release to the market.

Step five: Install the product software

To install the product on the wireless network, follow the steps for the method that you want to use (CD or download). Repeat the steps to install the software on each computer that will use the product wirelessly over the same network.
Important: If you get any firewall messages during installation, click unblock, accept, continue, yes, allow, or permit, or the installation will fail.
Follow these steps to download and install the software.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you will be prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 10: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Follow these steps to install the software with the product CD.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you are prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Insert the product CD into the CD drive of the computer, and then wait a few seconds for the software installer to start.
    If the installer does not start automatically, follow these steps to start it:
    Click the Windows icon (), click Computer, and then double-click the CD drive.
    NOTE:If the User Account Control screen opens, click Allow to continue.
  2. Follow the on-screen instructions to start the installation.
  3. In the Software to Install window, you can choose to install the recommended software or the minimum software.
    • Recommended: Click Next to install the recommended software. The recommended software provides full product functionality and includes valuable software, such as HP ToolboxFX and Help and Learn Center. HP designed this type of installation to work for most users.
    • Minimum: Click Click here for more install options to install the minimum software. The minimum software contains only the print driver. Install the minimum software if the computer is low on hard disk space.
  4. When prompted to choose a connection type, select the Network type, not the USB type. The USB cable is for the installation procedure only. (The installer prompts you when to connect and disconnect the USB cable.)
  5. Click Next.
      IMPORTANT: At this point, the installer searches, but does not find the product because it is not yet connected. This is expected behavior and does not indicate a problem with the setup. Click Next again to continue with the installation.
  6. Follow the on-screen instructions to finish installing the software.
Follow these steps for the Windows 7 operating system. Next, choose your connection type.
Follow these steps to install your HP product over a wired (Ethernet) network.
Important: You must follow these steps in the order presented.

Step one: Check requirements

Make sure you have the following items:
  • One of the following types of wired access points or routers: Ethernet router, switch, hub, or wireless router with Ethernet ports
  • A computer that connects to the wired access point or router
  • A Category 5 Ethernet cable to use for the HP product. (Do not use a standard telephone cable.)
    Figure 11: Cable comparison
    Ethernet cable and telephone cable
    1 - Ethernet cable
    2 - Telephone cable (do not use)
    Although an Ethernet cable looks similar to standard telephone cable, each has a different plug and a different number of wires. The plug on an Ethernet cable (also called an RJ-45 connector) is wide, thick, and always has eight wires. The plug on a telephone cable is narrower and has between two and six wires.
  • A network that uses one or more of the following protocols:
    • TCP/IP (IPv4 or IPv6)
    • Port 9100
    • LPR
    • DHCP
    • AutoIP
    • SNMP
    • Bonjour
    • SLP
    • WSD
    • NBNS
    • LLMNR

Step two: Change from USB connection to Ethernet connection

If you previously installed the software for a USB connection and now want to change to an Ethernet connection, follow these instructions to remove the USB installation before continuing.

Step three: Connect the HP printer to the network

Follow these steps to connect the product to the wired network.
  1. Remove any plug or protective cover from the Ethernet port on the back of the product.
    Figure 12: Remove plug
    Image: Remove the plug.
  2. Connect the Ethernet cable to the Ethernet port on the product. Then connect the other end of the cable to an available port on the wired access point or router.
    Figure 13: Connect the Ethernet cable
    Image: Connect the Ethernet cable.
  3. Wait 60 seconds before continuing. During this time, the network recognizes the product and assigns an IP address or host name for the product.
  4. On the product control panel, press OK.
  5. Print a Configuration Report.
    1. Load plain white paper into tray 1.
    2. Press the Right arrow button () to select Reports, and then press OK.
    3. Press the Right arrow button () to select Config report, and then press OK.
  6. Make note of the product IP address on the Configuration Report for future reference.

Step four: Decide whether to install with the product CD or download the software

Don’t worry if you don’t have the product CD! You can download the most current software available for your product from the HP Web site at no cost. The following information might help you decide which installation method to use:
CDDownload
For a new product:CD installation is a quick and easy method.If you do not have a CD, you can download the software you need.
For an older product:CD installation might not work if you are installing the product on a computer running a newer operating system that released AFTER the HP product released.Downloading the software provides the best results for your older product. Even though it takes more time than using the CD, downloading the latest software can help you avoid installation issues.

Downloading is the recommended method if your computer operating system released after the HP product released.
About the software:The software on the CD is current to the date of the product release.The software that you can download from the HP Web site is the most current software available for your product. HP often updates software and drivers AFTER the product and CD release to the market.

Step five: Install the software

When you are ready to begin, follow the instructions for the installation method that you want to use (CD or download). During the installation, choose the option for the network type of connection, not the USB option.
IMPORTANT: If you get any firewall messages during installation, click unblock, accept, continue, yes, allow, or permit, or the installation fails.
Follow these steps to download and install the software.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you will be prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 14: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Follow these steps to install the software.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you will be prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Press the Power switch or button to turn on the product.
  2. Insert the product CD into the CD drive of the computer, and then wait a few seconds for the software installer to begin.
    If the installer does not begin automatically, click the Windows icon (), click Computer, and then double-click the CD drive.
    NOTE:If the User Account Control screen opens, click Allow to continue.
  3. Follow the on-screen instructions to start the installation.
  4. In the Software to Install window, you can choose to install the recommended software or the minimum software.
    • Recommended: Click Next to install the recommended software. The recommended software provides full product functionality and includes valuable software, such as HP Toolbox and Help and Learn Center. HP designed this type of installation to work for most users.
    • Minimum: Click Click here for more install options to install the minimum software. The minimum software contains only the print driver. Install the minimum software if the computer is low on hard disk space.
  5. When prompted to choose a connection type, select the Network type, not the USB type. The USB cable is for the installation procedure only. (The installer prompts you when to connect and disconnect the USB cable.)
  6. Click Next.
      Important: At this point, the installer searches, but does not find the product because it is not yet connected. This is expected behavior and does not indicate a problem with the setup. Click Next again to continue with the installation.
  7. Follow the on-screen instructions to finish installing the software.
    NOTE:If you have previously installed the software and are changing the connection type from USB to Ethernet, click Add a device when the Uninstall the software or Add a device window opens.
    Important: The installer might ask if you want to check online for the latest installation updates for your product. For the best installation results, HP recommends that you click “Yes” to let the installer check for updates and download them for you.
If you have a wireless-capable HP product and want to install it on a wireless network, follow these steps.
Important: You must follow these steps in the order presented.

Step one: Gather the required network setup items

You must have the following items before you install the HP product on the wireless network:
Do not worry if you do not have all of the items yet! The HP Print and Scan Doctor
The HP Print and Scan Doctor is an automated tool designed to help you gather network information.
can help you gather some of these items.
  • Network name: The network name is the SSID
  • WEP key or WPA security passphrase
  • A computer that is connected to the wireless network
  • Internet access: HP recommends broadband Internet access such as cable or DSL
    NOTE:Internet access is not required for you to install your printer with a wireless connection. However, you do need Internet access to use Web Services or get product updates.
  • Your wireless-capable HP printer: Place it close to the computer during the installation procedure
  • A USB cable (used only during installation). Do not connect the cable now
HP designed a quick and easy tool that diagnoses and resolves many printing, scanning, and connectivity problems: The HP Print and Scan Doctor. If you have difficulty gathering your network information, try using the HP Print and Scan Doctor to retrieve your network name and password.
NOTE:The HP Print and Scan Doctor might not be available for all HP products, particularly older products. It is available for most products, however, and in most languages. This tool is available only for Windows operating systems. The tool is not available for Mac OS operating systems.
Follow these steps to download and run the HP Print and Scan Doctor, and then locate your network login information.
  1. Click the following link to download the HP Print and Scan Doctor.
  2. Make sure your computer meets the system requirements, and then click Download.
  3. When the Security Warning dialog box opens, choose one of the following methods to download the utility.
      1. In the Security Warning dialog box, click Run.
      2. When the Download Complete dialog box opens, click Run, and then click Run again on the Security Warning dialog box. The Print and Scan Doctor opens.
      1. In the Security Warning dialog box, click Save.
      2. When the Save As window opens, browse to your Desktop, and then click Save.
      3. When the download is complete, browse to where you saved the file, and then double-click the file to run the utility. The Print and Scan Doctor opens.
  4. On the Menu bar in the Print and Scan Doctor window, click Help.
  5. Click Show Advanced Info.
  6. Click Show Wireless Info.
  7. Under the Wireless Settings pane, identify the name of your network under SSID, and then identify the Network Key next to it in the list.

Step two: Prepare for installation

  1. Make sure the HP product, access point, and computer are all turned on, and that the computer is connected to the wireless network.
  2. Exit all applications running on your computer.
  3. Disconnect any USB or Ethernet cable that is connected to the HP product.
  4. If you previously installed the software for a USB connection and now want to change to a wireless network connection, follow these instructions to remove the USB installation before continuing.

Step three: Connect to the wireless network

Use one of the following methods to connect to the wireless network.
Follow these steps to connect your printer to the wireless network using WPS.
Video of connecting your wireless printer to a wireless network using WPS
The following video demonstrates how to use Wi-Fi Protected Setup to connect your printer to a wireless network.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
If your wireless router supports Wi-Fi Protected Setup (WPS), this is the simplest way to set up the product on a wireless network.
NOTE:This method requires a WPS-enabled wireless router to connect to the product.
  1. Press the WPS button on your wireless router.
  2. On the control panel, press and hold the Wireless button () for two seconds. Release the button when the wireless light starts blinking.
  3. Wait up to two minutes while the product establishes a network connection with the wireless router.
    NOTE:If the WiFi-Protected Setup (WPS) method is not successful, try using the product control panel, or the USB cable connection method.
If your wireless router does not support WiFi-Protected Setup (WPS), use one of the following options to connect the product to your wireless network.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, follow these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select Pushbutton, and then follow the on-screen instructions to connect to the wireless network.
    NOTE:Establishing the wireless connection can take a few minutes.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, complete these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select PIN. The product generates a unique PIN.
  4. Type the unique PIN into the wireless router's setup screen, and then click Save or Apply.
    NOTE:Establishing the wireless connection can take a few minutes.
If your wireless router does not support WiFi-Protected Setup (WPS), you can use this method to set up the product on a wireless network. Using a USB cable to transfer settings makes setting up a wireless connection easier. After the setup is complete, disconnect the USB cable.
Video of connecting your wireless printer to a wireless network with a USB cable
The following video demonstrates how to connect your wireless HP printer to a wireless network through a USB cable.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
  1. Insert the software CD into the CD drive.
  2. Follow the on-screen instructions. When prompted, select the Connect through a wireless network option.
  3. Connect the USB cable () to the product and the computer when prompted.
    CAUTION:Do not connect the USB cable until the installation program prompts you.
  4. When the installation is complete, print a Configuration Report to make sure that the product has an SSID name. Follow these steps to print a configuration report:
    1. Load plain white paper into tray 1.
    2. On the product control panel, press OK, and then press OK again to select Reports.
    3. Press the Right Arrow button ( ) to scroll to and select Config Report.
  5. When the Configuration Report prints, disconnect the USB cable () from the product.
    You have completed the software installation. Do not perform any more steps in this document.

Step four: Decide whether to install with the product CD or download the software

Don’t worry if you don’t have the printer CD! You can download the most current software available for your printer from the HP website at no cost. The following information might help you decide which installation method to use:
    For a new printer:CD installation is a quick and easy method.
    For an older printer:CD installation might not work if you are installing the printer on a computer running a newer operating system that released AFTER the HP printer released.

    For example, Windows Vista released in 2007. If HP manufactured your printer prior to that year, the CD that came with the printer might not work correctly on a computer running Vista.
    About the software:The software on the CD is current to the date of the printer release.
    For a new printer:If you do not have a CD, you can download the software you need.
    For an older printer:Downloading the software provides the best results for your older printer. Even though it takes more time than using the CD, downloading the latest software can help you avoid installation issues.

    Downloading is the recommended method if your computer operating system released after the HP printer released.
    About the software:The software you can download from the HP website is most current software available for your printer. HP often updates software and drivers after the printer and CD release to the market.

Step five: Install the product software

To install the product on the wireless network, follow the steps for the method that you want to use (CD or download). Repeat the steps to install the software on each computer that will use the product wirelessly over the same network.
Important: If you get any firewall messages during installation, click unblock, accept, continue, yes, allow, or permit, or the installation will fail.
Follow these steps to download and install the software.
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you are prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 15: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
The following video demonstrates how to install your HP Laserjet printer on a wireless network in Windows 7 using the CD provided with your printer.
NOTE:This video shows the HP Laserjet Pro 1525nw. The outside of the product might not look the same as your product, but the steps are the same.
.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
NOTE:Microsoft .NET 3.5 SP1 is required for the installer to run. If Microsoft .NET 3.5 SP1 is not installed you are prompted to install it. If you choose not to install it, only the basic print driver is installed.
  1. Press the Power switch to turn on the product.
  2. Insert the product CD into the CD drive of the computer, and then wait a few seconds for the software installer to begin.
    If the installer does not begin automatically, click the Windows icon (), click Computer, and then double-click the CD drive.
    NOTE:If the User Account Control screen opens, click Allow to continue.
  3. Follow the on-screen instructions to start the installation.
  4. In the Software to Install window, you can choose to install the recommended software or the minimum software.
    • Recommended: Click Next to install the recommended software. The recommended software provides full product functionality and includes valuable software, such as HP ToolboxFX and Help and Learn Center. HP designed this type of installation to work for most users.
    • Minimum: Click Click here for more install options to install the minimum software. The minimum software contains only the print driver. Install the minimum software if the computer is low on hard disk space.
  5. When prompted to choose a connection type, select the Network type, not the USB type. The USB cable is for the installation procedure only. (The installer prompts you when to connect and disconnect the USB cable.)
  6. Click Next.
      IMPORTANT: At this point, the installer searches, but does not find the product because it is not yet connected. This is expected behavior and does not indicate a problem with the setup. Click Next again to continue with the installation.
  7. Follow the on-screen instructions to finish installing the software.
    NOTE:If you have previously installed the software and are changing the connection type from USB to Ethernet, click Add a device when the Uninstall the software or Add a device window opens.
    IMPORTANT: The installer might ask if you want to check online for the latest installation updates for your product. For the best installation results, HP recommends that you click “Yes” to let the installer check for updates and download them for you.
Follow these steps to install the printer in the Windows 8 operating system. First, choose your connection type.
Follow these steps to install your printer over a wired (Ethernet) network.

Step one: Check requirements

Make sure you have the following items:
  • One of the following types of wired access points or routers: Ethernet router, switch, hub, or wireless router with Ethernet ports
  • A computer that connects to the wired access point or router
  • A Category 5 Ethernet cable to use for the HP product. (Do not use a standard telephone cable.)
    Figure 16: Cable comparison
    Ethernet cable and telephone cable
    1 - Ethernet cable
    2 - Telephone cable (do not use)
    Although an Ethernet cable looks similar to standard telephone cable, each has a different plug and a different number of wires. The plug on an Ethernet cable (also called an RJ-45 connector) is wide, thick, and always has eight wires. The plug on a telephone cable is narrower and has between two and six wires.

Step two: Change from a USB or wireless connection to an Ethernet connection (optional)

If you previously installed the software for a USB or wireless connection and now want to change to an Ethernet connection, follow these instructions to reconfigure the USB or wireless installation before continuing.
  1. Right-click or tap and hold the bottom left corner of the screen, and then click or tap Search.
  2. Click or tap Settings, and then type Devices in the Search box.
  3. Click or tap Devices and printers.
  4. Click Reconfigure your HP device.
  5. Follow the on-screen instructions to reconfigure your printer's installation.

Step three: Connect the printer to the network

Follow these steps to connect your printer to the Ethernet network.
  1. Remove any plug or protective cover from the Ethernet port on the back of the product.
    Figure 17: Remove plug
  2. Connect the Ethernet cable to the Ethernet port on the product, and then connect the other end of the cable to an available port on the wired access point or router.
    Figure 18: Connect the Ethernet cable
  3. Connect the power cord to the product, and then plug it into an electrical outlet.
  4. Turn the product on.

Step four: Download and install the software

When you are ready to begin, follow these steps to download and install the software. During the installation, choose the option to Connect through a Wired Network.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 19: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
If you have a wireless-capable printer and want to install it on a wireless network, follow these steps.

Step one: Prepare for installation

Follow these steps to prepare the printer for installation on the wireless network.
  1. Make sure that the printer, access point, and computer are all turned on, and that the computer is connected to the wireless network.
  2. Close all applications running on your computer.
  3. Disconnect any USB or Ethernet cable that is connected to the printer.
  4. If you previously installed the software for a USB or wired (Ethernet) connection and now want to change to a wireless network connection, follow these instructions to reconfigure the USB or Ethernet installation before continuing.

Step two: Connect to the wireless network

Use one of the following methods to connect to the wireless network.
Follow these steps to connect your printer to the wireless network using WPS.
Video of connecting your wireless printer to a wireless network using WPS
The following video demonstrates how to use Wi-Fi Protected Setup to connect your printer to a wireless network.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
If your wireless router supports Wi-Fi Protected Setup (WPS), this is the simplest way to set up the product on a wireless network.
NOTE:This method requires a WPS-enabled wireless router to connect to the product.
  1. Press the WPS button on your wireless router.
  2. On the control panel, press and hold the Wireless button () for two seconds. Release the button when the wireless light starts blinking.
  3. Wait up to two minutes while the product establishes a network connection with the wireless router.
    NOTE:If the WiFi-Protected Setup (WPS) method is not successful, try using the product control panel, or the USB cable connection method.
If your wireless router does not support WiFi-Protected Setup (WPS), use one of the following options to connect the product to your wireless network.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, follow these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select Pushbutton, and then follow the on-screen instructions to connect to the wireless network.
    NOTE:Establishing the wireless connection can take a few minutes.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, complete these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select PIN. The product generates a unique PIN.
  4. Type the unique PIN into the wireless router's setup screen, and then click Save or Apply.
    NOTE:Establishing the wireless connection can take a few minutes.
If your wireless router does not support WiFi-Protected Setup (WPS), you can use this method to set up the product on a wireless network. Using a USB cable to transfer settings makes setting up a wireless connection easier. After the setup is complete, disconnect the USB cable.
Video of connecting your wireless printer to a wireless network with a USB cable
The following video demonstrates how to connect your wireless HP printer to a wireless network through a USB cable.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
  1. Insert the software CD into the CD drive.
  2. Follow the on-screen instructions. When prompted, select the Connect through a wireless network option.
  3. Connect the USB cable () to the product and the computer when prompted.
    CAUTION:Do not connect the USB cable until the installation program prompts you.
  4. When the installation is complete, print a Configuration Report to make sure that the product has an SSID name. Follow these steps to print a configuration report:
    1. Load plain white paper into tray 1.
    2. On the product control panel, press OK, and then press OK again to select Reports.
    3. Press the Right Arrow button ( ) to scroll to and select Config Report.
  5. When the Configuration Report prints, disconnect the USB cable () from the product.
    You have completed the software installation. Do not perform any more steps in this document.

Step three: Download and install the printer software

Follow these steps to download and install the printer software. Repeat the steps to install the software on each computer that uses the printer wirelessly over the same network.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 20: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Choose your connection type for steps to install the HP product software for the Mac OS X operating system.
Follow these steps to install your HP product on a wired (Ethernet) network.
Follow these steps for Mac OS X 10.5 or 10.6 (Snow Leopard).
Step one: Check requirements
Make sure you have the following items:
  • One of the following types of wired access points or routers: Ethernet router, switch, hub, or wireless router with Ethernet ports
  • A computer that connects to the wired access point or router
  • A Category 5 Ethernet cable to use for the HP product. (Do not use a standard telephone cable.)
    Figure 21: Cable comparison
    Ethernet cable and telephone cable
    1 - Ethernet cable
    2 - Telephone cable (do not use)
    Although an Ethernet cable looks similar to standard telephone cable, each has a different plug and a different number of wires. The plug on an Ethernet cable (also called an RJ-45 connector) is wide, thick, and always has eight wires. The plug on a telephone cable is narrower and has between two and six wires.
Step two: Connect the printer to the network
  1. Remove any plug or protective cover from the Ethernet port on the back of the product.
    Figure 22: Remove plug
    Image: Remove the plug.
  2. Connect the Ethernet cable to the Ethernet port on the product. Then connect the other end of the cable to an available port on the wired access point or router.
    Figure 23: Connect the Ethernet cable
    Image: Connect the Ethernet cable.
  3. Wait 60 seconds before continuing. During this time, the network recognizes the product and assigns an IP address or host name for the product.
  4. On the product control panel, press OK.
  5. Print a Configuration Report.
    1. Load plain white paper into tray 1.
    2. Press the Right arrow button () to select Reports, and then press OK.
    3. Press the Right arrow button () to select Config report, and then press OK.
  6. Make note of the product IP address on the Configuration Report for future reference.
Step three: Decide how to install the software
Click the plus sign () for information on which software installation method to use.
The current full-feature HP software package for your product is available on the HP Software & Driver Downloads page. The download includes the HP print driver, HP Utility, and HP Installer to walk you through the installation steps. Depending on your product, the download might also include HP Scan software and the HP fax driver.
HP recommends this installation method for all new and older products.
Additionally, HP recommends that you use this installation method in the following cases:
  • You no longer have the product software CD
  • You updated your operating system to a version that released after your HP product released
Apple Software Updates is a quick and easy software download method available directly through the Mac.
You do not need to download a driver from the HP Software & Driver Downloads page if you use Apple Software Updates. This download method includes the HP print driver. Depending on your product, the download might also include HP Utility, scanning software, and the HP fax driver.
NOTE:If your product supports scanning, the software that you use to scan might be different than the software you used before installing Snow Leopard. Depending on your product driver update, use Preview, Image Capture, or the Scan icon from the print queue to scan.
Additionally, HP recommends that you use this installation method in the following cases:
  • You no longer have the product software CD
  • The updated full-feature HP software is not immediately available on the HP Software and Drivers page after the public release of a new operating system
  • You updated your operating system to a new version that released after your HP product released
Installing with the product CD is a quick and easy method. The CD includes the HP print driver, HP Utility, and HP Installer to walk you through the installation steps. Depending on your product, the CD might also include HP Scan software and the HP fax driver. This software is current to the date of the product release.
Important: If you try installing the product on a computer running a newer version of the operating system that released AFTER your HP product released, the CD installation method might not work. Visit HP Software & Driver Downloads to install the latest product software for the newer operating system.
Step four: Install the software
To install the HP product on the network, follow the steps for the method that you want to use. Repeat the steps to install the software on each computer that will use the HP product over the same network.
  1. Disconnect the USB cable from both the product and the computer (if you already connected it).
  2. Turn the product on.
  3. Browse to the Get Software and Downloads page: Get Software and Drivers .
  4. Check the instructions on the page, and then click the Plus sign (+) next to the correct heading for additional instructions:
      1. Type your product number in the window.
      2. Click Next. If necessary click your model in a list of similar products.
      3. Click Software and Driver Downloads.
      4. Click the drop-down arrow (), and then click your operating system.
      5. Click Next, and then continue to the next step
      1. Click the drop-down arrow (), and then click your operating system.
      2. Click Next.
      3. Continue to the next step
  5. Click the Plus sign () next to Driver, and then click the driver that you want to download.
    NOTE:HP recommends the Full Feature type of download, if available, to take advantage of all your product features.
  6. Read through the minimum system requirements and additional instructions. You can also click View directions () for complete download instructions.
  7. Click Download. If your browser opens a new dialog box, you might also need to click Save or Save File.
    The file downloads to your computer.
    Figure 24: Example of downloaded file
    Example of downloaded file
  8. Double-click the icon above the file name. The computer extracts the files and displays a disk image file icon above the product name.
    Figure 25: Example of disk image file
    Example of disk image file
  9. Double-click the disk image file.
  10. Double-click the HP Installer icon.
    The HP Installer program opens.
  11. When prompted, select your HP product, and then click OK.
  12. Follow the on-screen instructions to complete the installation.
Follow these steps to install the software with Apple Software Updates.
NOTE:Apple Software Updates is not supported in Mac OS X 10.5. Software for this operating system is available on the HP Software & Driver Downloads page and on the software CD.
  1. Click the Apple menu (), and then click System Preferences. The System Preferences window opens.
  2. Click Print & Fax. The Print & Fax window opens.
  3. Click the plus sign (). The name of your product displays.
  4. Select your HP product, and then click Add.
  5. Click Install, and then click Agree on the software license agreement window to install the software and add the product to the queue.
  6. After the installation process completes, verify that your product displays in the queue.
    NOTE:If the product was not added to the queue, Click the plus sign (), select your HP product, and then click Add.
  1. Insert the Macintosh product CD into the CD drive of the computer.
  2. Double-click the HP software disc icon that displays under the Macintosh HD icon.
  3. Double-click the HP Installer icon.
    The HP Installer program opens.
  4. When prompted, select your HP product, and then click OK.
  5. Follow the on-screen instructions to complete the installation.
Follow these steps for the Lion operating system.
Step one: Check requirements
Make sure you have the following items:
  • One of the following types of wired access points or routers: Ethernet router, switch, hub, or wireless router with Ethernet ports
  • A computer that connects to the wired access point or router
  • A Category 5 Ethernet cable to use for the HP product. (Do not use a standard telephone cable.)
    Figure 26: Cable comparison
    Ethernet cable and telephone cable
    1 - Ethernet cable
    2 - Telephone cable (do not use)
    Although an Ethernet cable looks similar to standard telephone cable, each has a different plug and a different number of wires. The plug on an Ethernet cable (also called an RJ-45 connector) is wide, thick, and always has eight wires. The plug on a telephone cable is narrower and has between two and six wires.
Step two: Connect the printer to the network
  1. Remove any plug or protective cover from the Ethernet port on the back of the product.
    Figure 27: Remove plug
    Image: Remove the plug.
  2. Connect the Ethernet cable to the Ethernet port on the product. Then connect the other end of the cable to an available port on the wired access point or router.
    Figure 28: Connect the Ethernet cable
    Image: Connect the Ethernet cable.
  3. Wait 60 seconds before continuing. During this time, the network recognizes the product and assigns an IP address or host name for the product.
  4. On the product control panel, press OK.
  5. Print a Configuration Report.
    1. Load plain white paper into tray 1.
    2. Press the Right arrow button () to select Reports, and then press OK.
    3. Press the Right arrow button () to select Config report, and then press OK.
  6. Make note of the product IP address on the Configuration Report for future reference.
Step three: Install the software
The software CD that shipped with your product is not supported in Lion. Follow these steps to download and install the current software from Apple Software Updates. Repeat these steps to install the software on each computer that will use the HP product over the same network.
NOTE:Older HP software might not be compatible with OS X 10.7 Lion. Do not try to install software that supports earlier versions of the Mac operating system, either from the original product CD or from HP Software & Driver Downloads.
  1. Click the Apple menu (), and then click System Preferences. The System Preferences window opens.
  2. Click Print & Scan. The Print & Scan window opens.
  3. Click the plus sign (). The name of your printer displays.
  4. Click Add Printer or Scanner.
  5. Select your printer, and then click Add.
  6. Click Install, and then click Agree on the software license agreement window to install the software and add the printer to the queue.
  7. After the installation process completes, verify that your printer displays in the queue.
    NOTE:If the product was not added to the queue, Click the plus sign (), select your printer, and then click Add.
Follow these steps to install the printer software on a Wired (Ethernet) network.
Step one: Check requirements
Make sure you have the following items:
  • One of the following types of wired access points or routers: Ethernet router, switch, hub, or wireless router with Ethernet ports
  • A computer that connects to the wired access point or router
  • A Category 5 Ethernet cable to use for the HP product. (Do not use a standard telephone cable.)
    Figure 29: Cable comparison
    Ethernet cable and telephone cable
    1 - Ethernet cable
    2 - Telephone cable (do not use)
    Although an Ethernet cable looks similar to standard telephone cable, each has a different plug and a different number of wires. The plug on an Ethernet cable (also called an RJ-45 connector) is wide, thick, and always has eight wires. The plug on a telephone cable is narrower and has between two and six wires.
Step two: Connect the printer to the network
Follow these steps to connect the printer to the Ethernet network.
  1. Remove any plug or protective cover from the Ethernet port on the back of the product.
    Figure 30: Remove plug
  2. Connect the Ethernet cable to the Ethernet port on the product, and then connect the other end of the cable to an available port on the wired access point or router.
    Figure 31: Connect the Ethernet cable
  3. Connect the power cord to the product, and then plug it into an electrical outlet.
  4. Turn the product on.
Step three: Download and install the software from the HP website
Follow these steps to download and then install the printer software from the HP website.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 32: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Follow these steps to install the product on a wireless network.
Important: Before you can install the product, your wireless network must already be set up. To set up your network, follow the instructions that came with your particular access point.
Follow these steps to install the software for Mac OS X 10.5 or 10.6 (Snow Leopard).
NOTE:HP recommends that you download the software from the HP website, or use the installation CD that came with your product. Apple Software Update installations do not support steps for connecting to the wireless network.
  • If you have not already installed your product, follow the steps in 'Option one: Wireless installation'.
  • If you want to change an existing connection type to a wireless network connection, follow the instructions in 'Option two: Change an existing USB or wired (Ethernet) connection to a wireless connection'.
If you have not previously installed the software, follow these steps to install your product on a wireless network.
Step one: Prepare for installation
  1. Make sure that you have the following requirements before you begin:
    • Network name: The network name is the SSID (Service Set Identifier).
    • WEP key or WPA security passphrase
    • A computer that is connected to the wireless network.
    • Internet access. HP recommends broadband Internet access such as cable or DSL.
    • Your wireless-capable HP product. Place it close to the computer during the installation procedure.
    • A USB cable (used only during installation).
    • Administrator privileges or password
  2. Make sure the product, access point, and computer are all on, and that the computer is connecting to the wireless network.
  3. Connect the USB Cable to the rear port of the HP product and to any USB port on the computer.
  4. Exit all applications running on your computer.
Step two: Decide how to install the software
Click the plus sign () for information on which software installation method to use.
Should I install using the software CD?
Installing with the product CD is a quick and easy method. The CD includes the HP print driver, HP Utility, and HP Installer to walk you through the installation steps. Depending on your product, the CD might also include HP Scan software and the HP fax driver. This software is current to the date of the product release.
Important: If you try installing the product on a computer running a newer version of the operating system that released AFTER your HP product released, the CD installation method might not work. Visit HP Software & Driver Downloads to install the latest product software for the newer operating system.
Should I download and install the software from HP Software & Driver Downloads?
The current full-feature HP software package for your product is available on the HP Software & Driver Downloads page. The download includes the HP print driver, HP Utility, and HP Installer to walk you through the installation steps. Depending on your product, the download might also include HP Scan software and the HP fax driver.
HP recommends this installation method for all new and older products.
Additionally, HP recommends that you use this installation method in the following cases:
  • You no longer have the product software CD
  • You updated your operating system to a version that released after your HP product released
Step three: Install the software
To install the HP product on the wireless network, follow the steps for the method that you want to use.
Method one: Install the software with the software CD
  1. Insert the Macintosh product CD into the CD drive of the computer.
  2. Double-click the HP software disc icon that displays under the Macintosh HD icon.
  3. Double-click the HP Installer icon.
    The HP Installer program opens.
  4. When prompted, select your HP product, and then click OK.
  5. Follow the on-screen instructions to complete the installation.
Method two: Download and install the software from the HP website
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 33: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Follow these steps to change the connection type with Bonjour.
NOTE:The product software or the in-OS driver must be installed, and the product must be connected to the wireless network to change the connection type with Bonjour.
  1. Click the Apple menu (), and then click System Preferences.
  2. Click Print & Fax.
  3. In the Printers section, click the name of your product, and then click the minus sign () to remove it.
  4. Click the plus sign ().
  5. Select your product from the list of Bonjour devices, and then click Add.
Follow these steps for OS X 10.7 (Lion).
NOTE:To install the product software for a wireless network connection, HP recommends that you download the software from the HP Web site or from Apple Software Updates. The product CD is not supported in Lion.
  • If you have not already installed your product, follow the steps in 'Option one: Wireless installation'.
  • If you want to change an existing connection type to a wireless network connection, follow the instructions in 'Option two: Change an existing USB or wired (Ethernet) connection to a wireless connection'.
If you have not previously installed the software, follow these steps to install your product on a wireless network.
Step one: Prepare for installation
To gather your network name (SSID) and password (WEP key or WPA passphrase), you can ask the person who originally set up your network, see the documentation that came with the access point, or contact the manufacturer. HP cannot set up or change the network SSID or the password.
  1. Make sure that you have the following requirements before you begin:
    • Network name: The network name is the SSID (Service Set Identifier).
    • WEP key or WPA security passphrase
    • A computer that is connected to the wireless network.
    • Internet access. HP recommends broadband Internet access such as cable or DSL.
    • Your wireless-capable HP product. Place it close to the computer during the installation procedure.
    • A USB cable (used only during installation).
    • Administrator privileges or password
  2. Make sure the product, access point, and computer are all on, and that the computer is connecting to the wireless network.
  3. Connect the USB Cable to the rear port of the HP product and to any USB port on the computer.
  4. Exit all applications running on your computer.
Step two: Decide how to install the software
Select a method to install the software.
Should I download and install the software from HP Software & Driver Downloads?
The current full-feature HP software package for your product is available on the HP Software & Driver Downloads page. The download includes the HP print driver, HP Utility, and HP Installer to walk you through the installation steps. Depending on your product, the download might also include HP Scan software and the HP fax driver.
HP recommends this installation method for all new and older products.
Additionally, HP recommends that you use this installation method in the following cases:
  • You no longer have the product software CD
  • You updated your operating system to a version that released after your HP product released
NOTE: Updated full-feature HP software might not be immediately available on the HP Software & Driver Downloads page after the public release of a new operating system. A release delay might be required for full testing and quality assurance of the final version of the operating system. If the software is not available, you can download the latest software using Apple Software Updates.
Can I install the software if the printer is already connected to the network?
Adding a network-connected printer to the queue is a quick and easy software download method using Apple Software Updates.
You do not need to download a driver from the HP Software & Driver Downloads page if you use Apple Software Updates. This download method includes the HP print driver. Depending on your product, the download might also include HP Utility, scanning software, and the HP fax driver.
HP recommends that you use this installation method in the following cases:
  • Your wireless network uses a router that does not support WiFi Protected Setup (WPS)
  • The updated full-feature HP software is not immediately available on the HP Software and Drivers page after the public release of a new operating system
  • You updated your operating system to a version that released after your HP product released
Should I download and install the software with Apple Software Updates?
Important: You must have a router that supports WiFi Protected Setup (WPS) to install the software with Apple Software Updates. If you do not have a WPS router, install the software using one of the other methods in this document.
Apple Software Update is a quick and easy software download method available directly through the Mac OS operating system.
You do not need to download a driver from HP Software & Driver Downloads if you install using Apple Software Update. This download method includes the HP print driver. Depending on your printer, the download might also include HP Utility, scanning software, and the HP fax driver.
NOTE:If your printer supports scanning, the software that you use to scan might be different than the software you used before upgrading your operating system. Depending on your printer driver update, you can use Preview, Image Capture, or the Scan icon from the print queue to scan.
Additionally, HP recommends that you use this installation method in the following cases:
  • You no longer have the software CD that shipped with your printer
  • The updated full-feature HP software for the new version of Mac OS is not immediately available on the HP Software & Driver Downloads page
  • You updated Mac OS to a new version that released after your printer released
  • You are doing a first time install of a new version Mac OS on a new Mac
  • You already installed HP software on a Mac running an earlier version of Mac OS and have updated to a new version of Mac OS
Step three: Download and install the software
The software CD that shipped with your product is not supported in Lion. Choose one of the following methods to install the software for a wireless connection. Repeat these steps to install the software on each computer that will use the HP product over the same network.
NOTE:Older HP software might not be compatible with OS X 10.7 Lion. Do not try to install software that supports earlier versions of the Mac operating system, either from the original product CD or from HP Software & Driver Downloads.
Method one: Download and install the software from the HP website
Follow these steps to download and install the software from the HP website. Repeat the steps to install the software on each computer that will use the HP product wirelessly over the same network.
NOTE: Updated full-feature HP software might not be immediately available on the HP Software & Driver Downloads page after the public release of a new operating system. A release delay might be required for full testing and quality assurance of the final version of the operating system. If the software is not available, you can download the latest software using Apple Software Updates or by adding a network-connected product to the queue.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 34: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.
Method two: Add the network-connected printer to the queue
Important: The product must already be connected to the wireless network to download and install the software.
  1. Click the Apple menu (), and then click System Preferences.
  2. Click Print & Scan.
  3. In the Printers section, click the name of your product, and then click the minus sign () to remove it.
  4. Click the plus sign ().
  5. Select your product from the list of Bonjour devices, and then click Add.
  6. Click Install, and then click Agree on the software license agreement window to install the software and add the product to the queue.
  7. After the installation process completes, verify that your product displays in the queue.
    NOTE:If the product was not added to the queue, Click the plus sign (), select your HP product, and then click Add.
Method three: Download and install the software using Apple Software Updates
NOTE:You must have a WiFi Protected Setup (WPS)-enabled router to connect the product to the wireless network. If you do not have this type of router, install the software using one of the other methods in this document.
Step one: Connect to the wireless network using WiFi Protected Setup
Follow these steps to connect your printer to the wireless network using WPS.
Video of connecting your wireless printer to a wireless network using WPS
The following video demonstrates how to use Wi-Fi Protected Setup to connect your printer to a wireless network.
If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube .
  1. Press the WPS button on your wireless router.
  2. On the control panel, press and hold the Wireless button () for two seconds. Release the button when the wireless light starts blinking.
  3. Wait up to two minutes while the product establishes a network connection with the wireless router.
Step two: Install the software
Follow these steps to download the current software from Apple Software Updates.
NOTE:Older HP software might not be compatible with OS X 10.7 Lion. Do not try to install software that supports earlier versions of the Mac operating system, either from the original product CD or from HP Software & Driver Downloads.
  1. Click the Apple menu (), and then click System Preferences. The System Preferences window opens.
  2. Click Print & Scan. The Print & Scan window opens.
  3. Click the plus sign (). The name of your printer displays.
  4. Click Add Printer or Scanner.
  5. Select your printer, and then click Add.
  6. Click Install, and then click Agree on the software license agreement window to install the software and add the printer to the queue.
  7. After the installation process completes, verify that your printer displays in the queue.
    NOTE:If the product was not added to the queue, Click the plus sign (), select your printer, and then click Add.
Follow these steps to change an existing connection type to a wireless connection using Bonjour.
NOTE:The product software must be installed, and the product must be connected to the wireless network to change the connection type with Bonjour.
  1. Click the Apple menu (), and then click System Preferences.
  2. Click Print & Scan.
  3. In the Printers section, click the name of your product, and then click the minus sign () to remove it.
  4. Click the plus sign ().
  5. Select your product from the list of Bonjour devices, and then click Add.
Follow these steps to install the printer software on a wireless network.
Step one: Prepare for installation
  1. Make sure that you have the following requirements before you begin:
    • Your network is already set up: Before you can install the printer, you must set up your wireless network. Follow the instructions that came with your router or access point to set up the network.
    • Obtain the network name and password: The network name is the SSID (Service Set Identifier). The WEP key or WPA security passphrase are other names for the password.
      Tip
      To gather the network name and password, you can ask the person who originally set up your network, see the documentation that came with the access point, or contact the access point manufacturer. HP cannot set up or change the network SSID, WEP key, or WPA passphrase.
    • Internet access: Required for HP Web Services only. HP recommends broadband internet access such as cable or DSL.
  2. Make sure that your wireless-capable printer, router, and computer are all turned on, and that the computer is connected to the wireless network.
  3. Place the printer close to the computer during the installation.
  4. Exit all applications running on your computer.
  5. Select one of the following options for steps to continue with the installation, depending on if you previously installed for a USB connection:
Step two: Connect to the wireless network
Use one of the following options to connect the product to your wireless network.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, follow these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select Pushbutton, and then follow the on-screen instructions to connect to the wireless network.
    NOTE:Establishing the wireless connection can take a few minutes.
  1. On the control panel, press the Wireless button (). Look at the control panel display to see if the Wireless Menu item has opened. If the Wireless Menu has not opened, complete these steps:
    1. On the product control panel, press OK.
    2. Press the Right arrow button () to select Network Setup, and then press OK.
    3. Press the Right arrow button () to select Wireless Menu, and then press OK.
  2. Press the Right arrow button () to select Wi-Fi Protected Setup, and then press OK.
  3. Press the Right arrow button () to select PIN. The product generates a unique PIN.
  4. Type the unique PIN into the wireless router's setup screen, and then click Save or Apply.
    NOTE:Establishing the wireless connection can take a few minutes.
Step three: Install the software
NOTE:To install the printer software for a wireless network connection, HP recommends that you download the software from the HP website. The printer CD is not supported in Mountain Lion, and Apple Software Update does not support steps for connecting to the wireless network.
  1. Turn on the printer.
  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.
  3. If the Welcome to HP Support page opens, follow these steps:
    1. In the Enter product name or number field, type your printer model or number.
    2. In the Questions or keywords field, type driver, and then press Enter.
      You might need to select your printer model number from a list of similar printer models.
    3. Next to the image of your printer, click the name of your printer.
      Figure 35: Example of the link to your printer homepage
      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.
  4. Select your operating system, and then click Next.
    A list of drivers and other downloads display.
  5. Scroll down the page, and then click Driver - Product Installation Software.
  6. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.
  7. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Related links

HP ePrint
Graphic and link to HP ePrintFor additional information related to setting up and using ePrint, click here to get started with ePrint .
HP Consumer Forums
See what other customers are saying at the HP forums .
HP LaserJet Pro CP1525nw Color Printer

HP Support forums

Find solutions and collaborate with others on the HP Support Forum
HP on YouTube