HP Media Center m1070.uk Desktop PC Troubleshooting
PrintMotherboard specifications table
| Feature/Specification | Description |
|---|---|
| Motherboard Description |
|
| Motherboard Supplier | ASUS |
| System BIOS Supplier | ASUS/Award |
| Board Form Factor | uATX |
| Processor Brand | Intel |
| Processor Socket Type | mPGA478 |
| Processor Family | Pentium 4HT |
| Maximum Processor Core Frequency | Up to 3.2 GHz P4 Northwood |
| Processor Front Side Bus | 800/533/400 MHz |
| Hyper Threading Support | Yes |
| Processor VRM Specification | Northwood FMB2 |
| Chipset 'North Bridge' | 865G |
| Chipset 'South Bridge' | ICH5 |
| Super I/O | SMsC LPC47M192-NC |
| Flash BIOS Device Type and Density | FWH 4 Mbit |
| Memory Type | DDR SDRAM (Supports duel channel) |
| Memory Speed | PC3200 (400 MHz), PC2700 (333 MHz), PC2100 (266 MHz) |
| Memory Sockets | Four DDR DIMM (184-pin) |
| Single or Dual Channel | Dual System Memory |
| Maximum Memory Supported | 4GB (4 x 512MB) unbuffered (HP and Compaq recommend 2GB) |
| AGP Graphics Support | Yes |
| AGP Graphics Maximum Mode | AGP 8x |
| Integrated Graphics Supplier | Intel |
| Integrated Graphics Shared (UMA) Memory | Up to 64 MB Intel DVMT- dynamic (32 MB if less than 256 MB system memory) |
| Graphics Configuration | Integrated on motherboard |
| Graphics Connector | AGP 8x (available) |
| TV-out Device or Configuration | No |
| Integrated Audio Type | AC'97 |
| AC'97 Codec Device | Realtek ALC650 |
| 5.1 (Dolby) Channel Audio Support | Yes, Six speaker mode (requires audio driver and software setting changes) |
| Passive Speaker Output (amplifed) | Speaker-out header |
| Rear Audio Jacks | Microphone, Line-in, Line-out, |
| Front Audio Connectors | Headphones, Microphone, Line-in |
| Ethernet 10/100 LAN Supplier | PCI Realtek RT8101L |
| Ethernet Configuration | Integrated, Down |
| IEEE 1394 Support | Configuration: Integrated on motherboard MAC/PHY Device: TI TSB43AB22 Maximum transfer rate: 400MBps Ports: Two total (1 front, 1 back) |
| IDE/ATAPI UDMA Modes | 2 IDE connectors
Supports. 2 IDE devices on each connector.
Supports UDMA 100/66/33 - requires an 40 pin/80 conductor cable for UDMA 66 and 100 disk drives 2 SATA connectors Supports. 1 Serial ATA-150 disk drive on each connector |
| Expansion Slots | One AGP, Three PCI, One Ultra ATA |
| USB Ports | Supports up to 8 USB v2.0 |
| USB Front/Rear Options | Up to four front, four rear |
| Rear External Ports | One serial, One parallel, One floppy, Two PS/2 (keyboard and mouse), One IEEE 1394, Four USB, One VGA Monitor |
| Front External Ports | Two USB, One IEEE 1394 |
| Fan support | Headers for CPU and System CPU Fan Speed Control for active fansink System Fan Speed Control |
| Available Manufacturer Options | Integrated graphics (G), Integrated LAN (L), Six speaker mode, Dolby 5.1 (6) Integrated 1394 (E) |
Motherboard layout and photos
Clearing the CMOS settings
The 3-pin J19 jumper allows you to clear date, time, and system setup parameter memories in CMOS. The onboard button cell battery powers the RAM data in CMOS, including system setup information.
CAUTION: Do not change any jumper setting while the computer is on. Damage to the motherboard can result.
- Turn off the PC and unplug the power cord.
- Move the J19 jumper cap from pins 1-2 (normal) to pins 2-3 (clear CMOS).
- Keep the J19 jumper cap on pins 2-3 for 5 to 10 seconds, then move it back to pins 1-2.
- Plug in the power cord and turn on the PC.
- Enter the BIOS setup to change the BIOS settings.
More for this product
HP Consumer Support Forum
Follow us
- Privacy Statement|
- Terms of Use|
- © 2013 Hewlett-Packard Development Company, L.P.